background image

INSTALLATION

WARNING! READ THE FOLLOWING INSTRUCTIONS CAREFULLY BEFORE USING OR WORKING WITH THE 200W LED BAR.

• The 200w LED Bar contains a glass lens over the LEDs. Please handle with care. 
•   Always gently place the 200w LED Bar on a clean, soft surface to avoid damaging the glass. 
•   In order to mount your 200w LED Bar properly, start by identifying a suitable support structure that you can mount your 200w LED Bar to.
•   Common support structures include pallet racks, trusses, structural channels, Unistrut, and rolling tables. 
•   The user is responsible for correct and safe installation and usage.
•   Please have two or more experienced, certified service personnel mount and install this device, in accordance with the applicable local laws and regulations.
• Best practices are to have a licensed electrician install your 200w LED Bar. 
•   Ensure the existing electrical system can support the voltage and current requirements of the 200w LED Bar.
•   When daisy chaining the 200w LED Bars together, make sure that you’re not attempting to connect more than the maximum amount of 200w LED Bars based on 
the voltage that your power cable and electrical system are rated for. Read the product specifications to see the maximum amount of 200w LED Bars that can be daisy 
chained together.

200W LED BAR POWER CORD

The power cord for the 200w LED Bar integrates both power and 0-10v dimming signal through fully shielded cabling and a single 5-pin IP67 rated connector. The 200w 
LED Bar features input and output cables that allow you to supply power and dimming signal by daisy chaining 15x to 20x 200w LED Bars together based on the voltage 
of your electrical system. If you're using our NX-1 Controller, you can control up to 100x 200w LED Bars per channel with the use of RJ14 splitters and interconnect 
cables (1 of each included with each power cord).

Содержание LUX-200-277-90




















Отзывы: