background image

Simply Connected

© 2014  Luxul. All Rights Reserved.

Other trademarks and registered trademarks are the property of their respective owners

11

 

„

When servicing the equipment and selecting a location for the antennas, it is important to note 
that a minimum distance of 20cm is required between personnel and the device or antenna to 
comply with the radio frequency exposure limit.

 

„

The antenna used for this transmitter must be installed to provide a separation distance of at 
least 20cm from all persons and must not be co-located or operating in conjunction with any 
other antenna or transmitter.

The following safety precautions should be observed:

 

„

Do not touch or move the antenna while the unit is transmitting or receiving.

 

„

Do not hold any component containing the radio such that the antenna is very close or touching 
any exposed parts of the body, especially the face or eyes, while transmitting.

 

„

Do not operate the radio or attempt to transmit data unless the antenna is connected; this 
behavior may cause damage to the radio.

FCC Statement—Wireless FCC 2.4GHz 802.11bgn

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one of the following measures:

 

„

Reorient or relocate the receiving antenna.

 

„

Increase the separation between the equipment and receiver.

 

„

Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.

 

„

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: 

Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other  
antenna or transmitter. 

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-
ment. This equipment should be installed and operated with minimum distance 20cm between the 
radiator & your body.

Содержание Xen XAP-1230













Отзывы: