Luxul AMS-1208P, Быстрая настройка

Страница: 4 / 32

2
QUICK INSTALLATION
Before„you„can„start„configuring„your„switch,„you’ll„need„to„install„it„in„a„safe,„stable„location,„then„connect„it„to„a„
network„and/or„connect„your„computer„to„the„switch„to„configure„it.„If„your„Luxul„switch„is„already„installed,„and„
connected„to„the„network,„and„you„can„access„it„from„your„computer,„you„can„skip„ahead„to„the„next„section„titled„
QUICK„SETUP:„SYSTEM.
1
Physical Installation
Luxul„AMS-„and„XMS-„series„switches„should„be„rack-mounted.„Install„the„switch„in„a„stable/safe„rack„to„avoid„any„possi-
ble„damage.„Make„sure„there„is„adequate„space„around„the„switch„for„adequate„ventilation„and„proper„heat„dissipation.„
Avoid„placement„in„direct„sunlight,„do„not„place„heavy„articles„on„the„switch„and„verify„that„the„outlet’s„ground„connec-
tion„is„functioning„properly.
Rack Installation
Use„the„included„L„brackets„for„convenient„installation„in„a„19-inch„server„or„audio„rack.„Use„four„screws„to„attach„the„
L-shaped„brackets„on„either„sides„of„the„switch,„and„horizontally„insert„the„switch„into„a„free„space„within„the„rack.„Use„
your„desired„hardware„to„affix„the„switch„supports„to„the„rack.„
2
Connecting Ethernet and Power
Ethernet and Power Connections
Use„any„RJ-45„cable„to„connect„the„switch„to„an„Ethernet-enabled„device„,„including„servers,„routers„and„other„switches.„
No„crossover„cable„is„necessary.„„
„
The„AMS-„and„XMS-„series„switches„support„10/100/1000„Mbps„Ethernet;„10/100„Mbps„half/full-duplex„mode„and„1000„
Mbps„full-duplex„mode.„All„RJ-45„ports„support„Auto„MDI/MDIX„and„can„be„used„as„ordinary„ports„or„as„Uplink„ports.„
The„rear„panel„features„an„AC„input„socket„and„power„switch.„Use„the„included„power„cable„to„connect„the„switch„to„a„
surge-protected„outlet.
Network Cabling
For„the„RJ-45„ports,„Luxul„recommends„Category-5,„super„Category-5„or„Category-6„unshielded„twisted„pair„(CAT5/
CAT5e/CAT6„UTP).„To„ensure„best„performance„and„stable„data„transmission„at„1000„Mbps,„use„Category-6„shielded„
twisted„pair.„Optical„fiber/cable„should„be„selected„based„on„the„wavelength„of„the„SFP„optical„module„to„be„used.„
c
c
CAUTION:
cMultiplecUplinkcchannelsccanccreatecloops,cresultingcincnetworkcfailure.cEnsureconlyconecUplinkcchannelcexistsc
betweencswitchescorcbetweencthecXMS-1010Pcandcacrouter.
c
n
NOTE:
ccWhencpoweringcup,cthecportcLEDsccorrespondingctocthecopticalcinterfacecmayctakecacmomentctocinitialize.cThiscisc
normalcascthecswitchcinitializationcandcstartupccompletes.
c
n
NOTE: ccForcoptimalcswitchcperformance,cdocnotcexceedctheccombinedcconsumptioncbudgetcforcallcexternalcPoEcdevicesc
connectedctocacPoEcswitch:c130wcforcAMS-1208P,c250wcforcAMS-2616Pcandc370wcforcAMS-2624PcandcXMS-2624P.
3
Preparing for Access
IP Addressing
If„the„Luxul„managed„switch„is„connected„to„a„network„with„a„192.168.0.X„address„scheme,„and„your„computer„shares„a„
similar„address„on„the„same„network,„you„can„skip„to„the„next„step,„
Access and Setup
.
c
n
NOTE:
cccIfcanothercdeviceconcyourcnetworkcsharescthec192.168.0.4c(orc192.168.0.3)caddress,cyou’llcneedctoctemporarilycreassigncorc
removecthatcdevicecwhilecyoucconfigurecthecswitch.