Luxibel LX305 Скачать руководство пользователя страница 2

 

LX305 

V. 02 – 22/05/2014 

©Velleman nv 

User Manual 

1.

 

Introduction 

To all residents of the European Union 
Important environmental information about this product 

This symbol on the device or the package indicates that disposal of the device after its lifecycle 

could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal 

waste; it should be taken to a specialized company for recycling. This device should be 

returned to your distributor or to a local recycling service. Respect the local environmental 

rules. 
If in doubt, contact your local waste disposal authorities. 

Thank you for choosing Luxibel

®

! Please read the manual thoroughly before bringing this device into 

service. If the device was damaged in transit, don't install or use it and contact your dealer. 

2.

 

Safety Instructions 

 

This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance by a person responsible for 

their safety. 
Children shall be supervised to ensure that they do not play with the appliance. 
Never let the device run unattended. 

 

Do not crimp the power cord and protect it against damage. 

Warning! If the power cord is damaged, it must be replaced by the manufacturer, its service 

agent, or similarly qualified persons in order to avoid any hazard. 

Make sure that the available voltage does not exceed the voltage stated in the specifications of 

this manual. 

This device falls under protection class I. It is therefore essential that the device be earthed. 

Have a qualified person carry out the electric connection. 

Be very careful during the installation: touching live wires can cause life-threatening 

electroshocks. 
Do not use the device when damage to housing or cables is noticed. Do not attempt to service 

the device yourself but contact an authorised dealer or service agent. 

 

Always disconnect mains power when device not in use or when servicing or maintenance 

activities are performed. Handle the power cord by the plug only. 

 

Caution: device heats up during use. Do not touch hot surfaces. Let the device cool down 

sufficiently after switching off before handling. 

 

 

Indoor use only. Keep this device away from rain, moisture, splashing and dripping 

liquids. Never put objects filled with liquids on top of or close to the device. 

 

Do not stare directly at the light source, as this may cause 

 

epileptic seizure in sensitive people 

 

temporarily loss of sight (flash blindness) 

 

permanent (irreversible) eye damage. 

 

 

Use an appropriate safety cable to fix the device (e.g. VDLSC7N or VDLSC8N). 

 

Install the device at a minimal distance of 0.5 m from flammable and explosive objects or 

substances. 

 

Respect a minimum distance of 0.5 m between the device’s light output and any illuminated surface. 

 

The maximum ambient temperature is 40 °C. Do not operate the device at higher temperatures. 

Содержание LX305












Отзывы: