Lux Tools BHA-800, Руководство пользователя

Страница: 21 / 96

GB
21
• Always comply with the all applicable domes-
tic and international safety, health, and work-
ing regulations.
Inform yourself before you start
work about the regulations that apply at the site
of the device.
• Remember that moving parts may also be
located behind ventilation and venting slots.
• Symbols affixed to your device may not be
removed or covered. Information on the device
that is no longer legible must be replaced imme-
diately.
Risks caused by vibrations
The vibration values specified in the technical data
represent the main uses of the device. The actual
existing vibrations during use may deviate from
these as a result of the following factors:
• Incorrect use of the product;
• Unsuitable tools inserted;
• Unsuitable material;
• Insufficient maintenance.
You can reduce the risks considerably by following
the tips below:
– Maintain the device in accordance with the
instructions in the operating instructions.
– Avoid working at low temperatures.
– When it is cold, make sure your body and your
hands, in particular, are kept warm.
– Take regular breaks and move your hands at the
same time to promote circulation.
Your device at a glance
►
P. 3, item 1
1. Tool receiving socket
2. Holder for the depth stop
3. Rotation direction switch
4. Locking button
5. On/Off switch
6. Lock button for depth stop
7. Lock button for mode changing switch
8. Mode changing switch
9. Additional handle
Scope of delivery
• Hammer drill
• Additional handle
• Depth stop
• Drill (3×)
• Chasing bit (2×)
• Operating instructions
Assembly
Mounting the depth stop
– Press locking switch (6) and keep it pressed.
– Insert the depth stop into the holder (2).
– Set the depth stop to the required depth.
– Release locking switch (6) again.
Operation
Removing a tool
►
P. 3, item 2
– Pull the tool holder (1) back.
– Remove the tool.
Inserting a tool
►
P. 3, item 2
– Pull the tool holder (1) back.
– Insert the required tool with a slight turn until the
tool holder locks.
Selecting the operating mode
►
P. 3, item 3
Press the lock button (7) and set the switch (8) to the
required operating mode:
• Position
[ ]
for drilling without the hammer
function into wood, metal, ceramics and plastics
and for the screwdriver function.
• Position
[ ]
for hammer drilling in cement or
stone.
• Position
[ ]
for chasing in cement or stone.
Before putting the unit into operation, read
and observe the instructions for use.
CAUTION! Risk of injury due to vibra-
tions!
Vibrations may, in particular for per-
sons with circulation problems, cause dam-
age to blood vessels and/or nerves.
If you notice any of the following symp-
toms, stop working immediately and con-
sult a doctor. Numbness of body parts, loss
of sense of feeling, itching, pins and nee-
dles, pain, changes in skin colour.
CAUTION! Risk of injury
Shortly after
being used, the tool may be very hot. Risk
of burning! Allow a hot tool to cool down.
Never clean a hot tool with flammable liq-
uids.
WARNING! Risk of injury!
Make sure that
when installing the tool that it fits securely
in the clamping chuck and is not at an
angle.
Note:
Clean and grease the shaft of the tool
before inserting.
NOTICE! Risk of damage to the unit!
Only change operating mode when the
device is switched off.
NOTICE! Risk of damage to the unit!
Do
not use settings
[ ]
,
[ ]
and
[ ]
for
screwing in and removing screws. Do not
use settings
[ ]
and
[ ]
for chasing.
Note:
The position
[ ] is only used
to
rotate the tool to the required position. To
chase, the switch (8) must be set to posi-
tion
[ ]
.
Meisselhammer_380381.book Seite 21 Donnerstag, 11. Mai 2017 2:00 14