8
GB
O R I G I N A L I N S T R U C T I O N S
OPERATION OF THE DEVICE
Assembling and dismantling of the juice extractor
The juice extractor should be assembled as it is described below. Only correct assembly ensures an efficient and safe operation.
ATTENTION!
During all assembly operations, turn off the device and unplug it from the power supply.
ATTENTION!
During the assembly and disassembly of the rotating sieve you should take extreme caution, due to the risk of injury
from sharp sieve elements.
Put on the cover of the rotary sieve (II) on the juice extractor construction, and then mount on the rotor the ratary sieve (III). Gently
push the sieve down until it snaps on the rotor - you will hear a click. If you cannot lift the sieve by gently prying the flange around
the upper edge, and the sieve upper rim is below the top edge of the cover, this means the proper installation.
Place the pulp container on the basis, so that its top edge will be under the flange of sieve cover (IV).
Put the lid on the cover and container, so that the entry hole will be over the rotary sieve, and the lid edge will be at the same
level as the edge of sieve cover and pulp container (V). The lid has a protrusion (VI), which makes it easier to perform correct
installation of the lid.
Secure the lid with clamp (VII). Make sure that the clamp has been blocked in both the hollows on the top of the lid (VIII).
The juice container should be placed under the outlet hole, then cover it with the lid (IX). A lid will prevent the juice splashing
during squeezing.
Correctly assembled juice extractor, which is ready to work, looks like the one on figure (X).
In the case of an dismantling you should raise the clamp slightly upwards, so as to slide it out from the holes, and then rotate the
clamp so that it will be possible to dismantle the cover lid. Disassembly should be done in reverse order to assembly.
In order to disassemble the rotational sieve, you must przyze it for the flange around edge, and then pull it up.
Attention! The device has two safety switches. They do not allow for accidental start of the device when mounting, or when the
device incorrectly assembled. The first switch is located on the edge of the enclosure and is deactivated by the protrusion of the
housing cover. The second switch is deactivated by the appropriate blocking of lid clamp.
Pressing out the juice
Fruits and vegetables should be washed and cut into pieces, which are smaller than the input hole of the juice extractor, so that it
is possible their free placing in the input hole. Fruits and vegetables with a thick skin, or skin that is not normally eaten, should be
peeled. You must also remove all stones and hard, not fit for human consumption, parts of sand vegetables.
Plug the juice extractor to the power supply and turn on it.
The switch allows you to set three modes:
O – machine switched off
1 – lower speed of the sieve, matched to the juicing of soft fruits and vegetables
2 – higher speed of the sieve, matched to the juicing of all fruits and vegetables
Wait to achieve full rotation speed by the sieve, then put in fruits or vegetables through the entry hole.
ATTENTION!
If, when you turn the device on, it falls into it in vibration, issues an unusual sound or there are visible other signs of
malfunction, you should immediately turn it off, disconnect from the power supply and check the cause of malfunctioning.
To obtaing the maximum performance of juicing you should push the fruits or vegetables, which are placed in the juice extractor,
with the supplied pusher. Pusher has the cut, which should be fit to the guide, which is located inside the entry hole of juice extrac-
tor (XI). Otherwise, it will not be possible to use the pusher in its full capacity. The guide also prevents the catching of pusher by
the rotary sieve in the case of pressing the harder fruits or vegetables.
ATTENTION!
It is forbidden to push the fruits or vegetables with anything other than the pusher, which is a part of the juice extrac-
tor. Especially it is forbidden pushinb by using your fingers, hands or cutlery. It is also prohibited to use the pusher from a different
model of juice extractor. The rotational sieve may catch fingers, hands or any other object, which threatens a serious injury.
During juicing you should constantly check whether containers for juice and pulp do not fill and it is necessary to empty them.
Before emptying the containers you should turn off the juice extractor, wait until the complete stop of sieve rotation, disconnect
the power cord from the mains outlet, and then start a partial disassembly of the juice extractor, which would allow you for the
disconnection of the pulp container. Properly mounted guard of rotational sieve will allow you to raise it a little, which would making
it easier to disconnect and connect the pulp container without disassembly of the sieve and shielding.
If, in the course of juicing, the rotational sieve stops unexpectedly, for example, as a result of placing a too hard fruit or vegetable
in the sieve or applying to strong pressure to it, you should immediately turn off the device, disconnect it from the power supply and
dissassembly the device. Then clean all parts according to the instructions and proceed to work after their installation.
After you have finished juicing, turn off juice extractor, wait until the complete stop of rotation of sieve, disconnect the power cord
from the wall outlet, remove the device and proceed to its maintenance.
