background image

4

  

U.L. Model No.: 52-CL

Before assembling your ceiling fan, refer to section 

on proper method of wiring your fan (page 6). If you 

feel you do not have enough wiring knowledge or 

experience, have your fan installed by a licensed 

electrician.

 

WARNING

!

This Manual Is Designed to Make it as Easy as Possible for You to Assemble, 

Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips Head Screwdriver 

One Stepladder

One 1/4” Blade Screwdriver 

One Wire Stripper

Materials

Wiring outlet box and box connectors must be of type 

required by the local code . The minimum wire would be 

a 3-conductor (2-wire with ground) of following size:
  Installed Wire Length 

Wire Size A .W .G .

 

Up to 50 ft . 

14

 

50-100 ft . 

12

1. Unpacking Instructions 

 (Continued)

Controls 

(Sold Separately)

This Ceiling Fan may be used with the following 

Accessories (Purchased Separately): SW46 4-Speed 

Slide Wall Control, SW90 Fan & Light Dual Slide Wall 

Control and LED Light Fixtures .

2. Electrical Requirements

Your new Ceiling Fan will require a Grounded Electrical 

Supply line of 120 Volts AC, 60 Hz, 15 Amp Circuit .

To reduce the risk of fire, electric shock, or personal 

injury, mount fan to outlet box marked “Acceptable 

for Fan Support of 22.7 kg. (50 lbs.) or less”, and 

use screws supplied with outlet box. Most outlet 

boxes commonly used for support of light fixtures 

are not acceptable for fan support and may need to be 

replaced. Consult a qualified electrician if in doubt.

 

WARNING

!

Turning off wall switch is not sufficient. To avoid 

possible electrical shock, be sure electricity is turned 

off at the main fuse box before wiring. All wiring 

must be in accordance with National and Local codes 

and the ceiling fan must be properly grounded as a 

precaution against possible electrical shock.

 

WARNING

!

To avoid fire or shock, follow all wiring instructions 

carefully.
Any electrical work not described in these 

instructions should be done or approved by a licensed 

electrician.

 

WARNING

!

The Outlet Box must be securely anchored and capable 

of withstanding a load of at least 50 pounds .
If your Fan is to replace an existing ceiling light fixture, 

turn Electricity Off at the Main Fuse Box at this time and 

remove the existing light fixture .

Please call Customer Service at 1-800-777-4440 

if you have any questions about installation and 

operation of this Ceiling Fan .

Содержание kathy ireland home













Отзывы: