background image

LUMASCAPE ASIA PACIFIC

  Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia

Phone +61 7 3854 5000 | Fax +61 7 3854 5001 | Email: [email protected]

www.lumacape.com

LUMASCAPE NORTH AMERICA

  1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA

Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: [email protected]

www.lumacape.com

Products and specifications are subject to change without notice.

1 / 7

 IN0167 181126 CE UL

INSTALLATION INSTRUCTIONS

INGROUND / INGRADE
LED UPLIGHT

USA I Australia I Asia I Middle East I Europe

Erden 

E8

 

LS3080

IP68

DANGER

ISOLATE LUMINAIRE FROM POWER

Failure to isolate power 

supply before installation or 

maintenance may result in 

fire, serious injury, electric 

shock, death and may 

damage the luminaire.

READ ALL SAFETY INSTRUCTIONS FIRST

Warranty Void if not installed as per installation instructions and in 
compliance with the local electrical code.

N653

LS640-K 84 

Pre-Installation 

 ›Follow instructions carefully, failure to do so will void 

warranty.

 ›Ensure installation complies with local law and 

applicable standards.

 ›Input voltage range 110-277V AC 50/60Hz.
 ›Requires Lumascape PowerSync Master LS6540 for 

dimming or color changing. 

 ›Never make connections whilst the power is 

connected.

 ›All connections must be kept dry; failure to do so 

may result in product reliability issues.

 ›Ensure mains input power is surge protected.
 ›Do not make modifications or alter the product.
 ›Keep luminaire clean and free of debris.

Содержание LS3080








Отзывы: