Ludlum Measurements 15 Скачать руководство пользователя страница 14

Страница: 14 / 44

Model 15

Technical Manual

Section 4

Ludlum Measurements, Inc.

Page 4-1

June 2020

Identification of Controls and
Functions

Meter

: 6.4 cm (2.5 in.) arc, 1 mA analog type with pivot-and-jewel

suspension. Typical meter dial is 0-500 cpm, 0-2.5 kV and

BAT TEST

Connector

: used to connect the detector to the instrument. Typically

series

but can be

BNC,

MHV,

UHF,

or others.

Range Selector Switch

: a six-position switch marked

OFF

BAT

, ×1000,

×100, ×10, and ×1. Turning the range selector switch from

OFF

BAT

provides the operator with a battery check of the instrument. A

BAT

TEST

scale on the meter provides a visual means of checking the

battery-charge status. Moving the range selector switch to one of the
range multiplier positions (×1000, ×100, ×10, ×1) provides the operator

with an overall range of 0 to 500,000 cpm. Multiply the scale reading by
the multiplier to determine the actual scale reading.

Battery Compartment

: sealed compartment to house two

cell

batteries.

AUD ON-OFF Toggle Switch

: in the

position, operates the

unimorph speaker, located on the left side of the instrument. The
frequency of the clicks is relative to the rate of the incoming pulses. The

higher the rate, the higher the audio frequency. This switch should be
turned

OFF

when not required, in order to reduce battery drain.

RES Pushbutton

: When depressed, this button provides a rapid means

of driving the meter needle to zero.

F/S Toggle Switch

: provides meter response. Selecting the fast,

position, of the toggle switch provides 90% of full-scale meter deflection
in four seconds. In the slow,

position, 90% of full-scale meter

deflection takes 22 seconds. In the

position there is fast response and

large meter deviation. The

position should be used for slow response

and damped meter deviation.

Section

Содержание 15













































Результаты поиска

Содержание 15

Отзывы:

Бренды по названию

Популярные бренды

Ludlum Measurements 15, Руководство пользователя

Результаты поиска

Содержание 15

Отзывы:

Бренды по названию

Популярные бренды