Lucent Technologies Victory WP-93936 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 116

background image

Lucent Technologies Victory Class Batteries WP-93936

8 - 4 Maintenance

Issue 1 May 2000

Check and Record Individual Cells for Crystals, continued

If Crystals Appear
on All Cells in a
String

If lead-sulfate crystals appear on all cells in a string, check the
following as possible causes for the abnormal condition:

•

Rectifier voltage: The appearance of lead-sulfate crystals may
indicate a low battery plant float voltage. Check the battery plant
float voltage and make appropriate rectifier adjustments.

•

Plant discharge: A battery discharge resulting from a power failure
or other reasons may produce lead-sulfate crystals on the cells.
This is normal with all lead-acid cells since lead sulfate is the
material produced when a lead-acid cell is discharged. If the cause
of the lead-sulfate crystals is a recent discharge, the crystals will
disappear when the cells have been fully recharged on float
(usually within two weeks). Check plant records to determine if a
discharge has occurred. Another method of determining if a plant
discharge has occurred is to measure cell specific gravities.
Readings of .03 less than the nameplate values on most cells would
be a clear indication that a plant discharge has occurred.

•

If the presence of lead-sulfate crystals on all cells in a string is not
attributable to a plant discharge or improper rectifier voltage,
report the condition to Lucent Technologies.

«
...
78
79
80
81
82
...
»

Содержание Victory WP-93936





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Victory WP-93936

Бренд: Manfrotto Страницы: 4

Бренд: TaylorMade Страницы: 5

Бренд: VDO Страницы: 91

Бренд: CALEFFI Страницы: 20

Бренд: Panasonic Страницы: 443

Бренд: Panasonic Страницы: 132

EASA-PHONE KX-T30810

Бренд: Panasonic Страницы: 16

Бренд: Gardener's Страницы: 2

Electronic Parking Disc II

Бренд: Jacob Jensen Страницы: 28

Бренд: Monacor Страницы: 2

MIW-DUAL-SIGNAL-BAY

Бренд: Panamax Страницы: 2

Бренд: pleasant hearth Страницы: 6

Бренд: R&G Страницы: 12

Бренд: Datalogic Страницы: 5

Бренд: Aptina Страницы: 147

MultiConnect Conduit Series

Бренд: Multitech Страницы: 2

Бренд: Sensit Страницы: 4

Бренд: Whispbar Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды