Lucent Technologies Stinger OC3-ATM Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 34

Lucent Technologies Stinger OC3-ATM Скачать руководство пользователя страница 25

Configuring the OC3-ATM Trunk Module

Checking OC3-ATM trunk interface status

Stinger OC3-ATM Trunk Module Guide

1-11

admin> read oc3-atm {1 trunk-module-2 1}

OC3-ATM/{ shelf-1 trunk-module-2 1 } read

admin> set enabled = yes

admin> set spare-physical-address shelf = 1

admin> set spare-physical-address slot = 18

admin> set spare-physical-address item-number = 2

admin> set sparing-mode = automatic

admin> write

OC3-ATM/{ shelf-1 trunk-module-2 1 } written

Because one port is a spare, the administrator increases the number of VCCs that can be
handled by the first trunk port from 8K (8192) to 16K (16384). This increase allows the system
to handle the full 32K (32768) maximum number of VCCs on the trunk-side, even though it
has only three active ports. The following commands increase the valid range of VCIs from 8K
to 16K on port 1 of the first trunk module:

admin> read oc3-atm {1 trunk-module-1 1}

OC3-ATM/{ shelf-1 trunk-module-1 1 } read

admin> set line-config vpi-vci-range = vpi-0-255-vci-32-16383

admin> write

OC3-ATM/{ shelf-1 trunk-module-1 1 } written

Checking OC3-ATM trunk interface status

The Stinger unit creates an OC3-ATM-Stat profile for each of its OC3 interfaces. The profiles
provide information about the state of the physical interfaces, error counters, and ATM framer
status information. The Performance-Monitoring and Interval-Performance-Monitoring
subprofiles provide counters for the SONET payload.

The following display shows OC3-ATM-STAT parameters for the physical interface, with
sample settings for an active line:

[in OC3-ATM-STAT/{ shelf-1 trunk-module-2 1 }]

physical-address* = { shelf-1 trunk-module-2 1 }

line-state = active

spare-physical-address = { any-shelf any-slot 0 }

sparing-state = sparing-none

vpi-vci-range = vpi-0-255-vci-32-8191

vc-switching-vpi = 0

vcc-vpi = [ 0 0 0 0 0 0 0 ]

loss-of-signal = False

loss-of-frame = False

out-of-frame = False

section-state = sonet-section-active-no-defect

path-state = sonet-path-active-no-defect

ais-receive = False

yellow-receive = False

out-of-cell-delineation = False

loss-of-cell-delineation = False

aps-receive = False

rsop-bip-error-count = 0

«
...
23
24
25
26
27
...
»

Содержание Stinger OC3-ATM



































Отзывы:

Нет отзывов