Lucent Technologies Stinger OC3-ATM Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 34

Lucent Technologies Stinger OC3-ATM Скачать руководство пользователя страница 13

About This Guide

Stinger documentation set

Stinger OC3-ATM Trunk Module Guide

xiii

Stinger ADSL 24-Port Line Interface Module (LIM) Guide
Stinger ADSL 48-Port G.lite Line Interface Module (LIM) Guide
Stinger Copper Loop Test (CLT) Module Guide—includes operating instructions
Stinger DS3-ATM Trunk Module Guide
Stinger E3-ATM Trunk Module Guide
Stinger HDSL2 32-Port Line Interface Module (LIM) Guide
Stinger IDSL 32-Port Line Interface Module (LIM) Guide
Stinger OC3-ATM Trunk Module Guide (this manual)
Stinger SDSL 48-Port Line Interface Module (LIM) Guide
Stinger T1 and E1 Modules Guide

•

Configuration:

–

Stinger ATM Configuration Guide. Describes how to use the command-line interface
to configure Asynchronous Transfer Mode (ATM) operations on a Stinger unit. The
guide explains how to configure permanent virtual circuits (PVCs), and shows how to
use standard ATM features such as quality of service (QoS), connection admission
control (CAC), and subtending.

–

Stinger Private Network-to-Network Interface (PNNI) Supplement. Provides
quick-start instructions for configuring PNNI and soft PVCs (SPVCs), and describes
the related profiles and commands in the Stinger command-line interface.

–

Stinger SNMP Management of the ATM Stack Supplement. Describes SNMP
management of ATM ports, interfaces, and connections on a Stinger unit to provide
guidelines for configuring and managing ATM circuits through any SNMP
management utility.

–

TAOS RADIUS Guide and Reference. Describes how to set up a TAOS unit to use the
Remote Authentication Dial-In User Service (RADIUS) server and contains a
complete reference to RADIUS attributes.

•

Administration and troubleshooting:

–

Stinger Administration Guide. Describes how to administer the Stinger unit and
manage its operations. Each chapter focuses on a particular aspect of Stinger
administration and operations. The chapters describe tools for system management,
network management, and Simple Network Management Protocol (SNMP)
management.

•

Reference:

–

Stinger Reference. An alphabetic reference to Stinger profiles, parameters, and
commands.

–

TAOS Glossary. Defines terms used in documentation for Stinger units.

«
...
11
12
13
14
15
...
»

Содержание Stinger OC3-ATM



































Отзывы:

Нет отзывов