Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 331

Страница: 331 / 365

B-6

Maintenance

To use Table B-1, first locate the item you want. A triangle ( ) indicates where you can obtain it.

SOURCE (U.S.)

System Modules and Wiring:

Lucent

Direct

Catalog

Sales

(800) 451-2100

Lucent

Technologies

Authorized

Dealer

Lucent

Technologies

National Parts Sales

Center

(800) 222-7278

Lucent

Technologies

Sales

Office

(800) 247-7000

Table B-1. Sources of Additional Equipment and Replacement Parts (U.S.)

Continued on next page

To locate the nearest Lucent Technologies Authorized Dealer, check your local telephone directory’s yellow pages.

PARTNER ACS Processor module

Includes module, three 7-ft. line cords, and installation
instructions

Line/Extension module (206E)

Includes module, two 7-ft. line cords, and installation
instructions

Line module (400E/200E)

Includes module, four 7-ft. line cords, and installation
instructions

2-Slot Carrier

5-Slot Carrier

Cover for 5-Slot Carrier

AC power cord

Line cord (D2R)

Connects 206E and 400E modules to network interface
(clear color). Specify length: 7 (standard length), 14, or 25 ft.

267F2 bridging adapter

Connects two devices to one extension

In-Range Out-of-Building (IROB) protector

Required when installing extensions in another building from
the control unit (two required per PARTNER-model
telephone, one per standard phone or device)

Lucent Technologies 146G Surge Protector–SCL/8

Required when installing a Contact Closure–controlled
device outside the building to protect the control unit from
electrical surges.

Z300A Electromagnetic Interference (EMI) Filter

Includes filter, 7-ft. line cord, and installation instructions

267C line adapter

Splits two outside lines from an RJ14 network interface jack,
so that each line has its own modular plug (do not use at
extension jacks)

355A/355AF adapter

Connects call reporting device to primary processor module

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Результаты поиска

Содержание PARTNER Advanced Communications System Release 1.0

Отзывы:

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренды по названию

Популярные бренды

Lucent Technologies PARTNER Advanced Communications System Release 1.0, Инструкция по программированию и эксплуатации

Результаты поиска

Содержание PARTNER Advanced Communications System Release 1.0

Отзывы:

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренды по названию

Популярные бренды