Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 251 | Manualshive

Страница: 251 / 365

background image

SMDR Output Format (#610)

Description

Call Reporting (often referred to as

Station Message Detail Recording or SMDR)

provides detailed tracking of telephone usage in a printed report. This System
Programming procedure allows you to specify whether a maximum of 15 digits or
24 digits is printed for dialed numbers in the Number field on the call report. The
longer field is useful for businesses, such as law offices and hotels, that need to
record many digits for outgoing calls for billing purposes.

Before changing to 24 digits, check the documentation for your call accounting
device to verify that 24 digit output is supported.

Related Features

You can use

SMDR Record Type (#608)

to specify the type of calls to be

included on call reports.

When you change the output format, the length of the Number field is
adjusted for the next call record that prints. To print a new header, use

SMDR Top of Page (#609)

Considerations

This feature requires special hardware and/or software. For more
information, see “Call Reporting Devices (SMDR)” in Chapter 4.

If the output format is set to 15 digits and a “?” prints as the last digit of a
dialed number on a call report (indicating that the digits dialed exceed the
15 digits the Number field can hold), you may want to change the output
format to 24 digits.

Valid Entries

1 = 15 Digits

✔

2 = 24 Digits

Programming

(See Figure 2-3 in Chapter 2 for the location of special programming buttons
such as

s

and

e

on system phones.)

To change the maximum number of digits for dialed numbers that can print on
call reports:

1.

Press

f

0

0

s

s

#

6

1

0

at extension 10

or 11.

2.

Press

D

until the appropriate value displays.

3.

Select another procedure or exit programming mode.

5-158

SMDR Output Format (#610)

«
...
249
250
251
252
253
...
»

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренд: JBL Страницы: 24

Бренд: Panamax Страницы: 16

Бренд: N-Com Страницы: 32

Бренд: ENTRYPASS Страницы: 27

HCS-4100/50 Series

Бренд: Taiden Страницы: 223

Бренд: H&B Страницы: 9

Бренд: btsr Страницы: 73

Бренд: Creator Electronics Страницы: 52

Бренд: LG Страницы: 20

Бренд: LG Страницы: 36

Бренд: Mitsubishi Electric Страницы: 17

Бренд: Mitsubishi Electric Страницы: 20

Бренд: Mitsubishi Electric Страницы: 48

Бренд: Mitsubishi Electric Страницы: 20

MELDAS 600 Series

Бренд: Mitsubishi Electric Страницы: 141

CITY MULTI PAR-40MAAU

Бренд: Mitsubishi Electric Страницы: 88

MELDAS FCU6-DX561

Бренд: Mitsubishi Electric Страницы: 53

CITY MULTI PAR-40MAAU

Бренд: Mitsubishi Electric Страницы: 224

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды