138-NO132A_Rev00_2020-11
Seite 2 von 3
www.LSL.eu
Mounting and safety instructions
LSL handlebar grips „NOVA-RS“ for handlebar diameter
7/8in (22,2mm)
Thank you for buying a LSL product. Because of our passion for motorcycles all our products are designed to meet your needs as a motorcyclist. We wish you always a safe and pleasant ride with your new LSL product from Paaschburg
& Wunderlich GmbH.
Please read this manual carefully prior to installation
Only when professionally installed is the statutory warranty and driving safety fulfilled. Pay attention to the information in the operating instructions of the vehicle or specifications of the vehicle manufacturer. Failure to follow the
assembly instructions can damage your vehicle and void the warranty. This is necessary to not affect the riding safety. No liability is accepted for consequential damage.
The unauthorized reworking and / or modification of the product can lead to the failure of the function and is not permitted. No entry in the vehicle documents or the carrying of any documents is necessary.
Please keep these instructions for later use!
Scope of delivery:
•
1 Pair of handlebar grips
Installation of the handlebar grips:
1.
Before the installation, make sure that your vehicle is standing safe. Before the installation, check the appropriate outer diameter of the handlebars or the inner diameter of the grips with a calliper.
2.
Dismantle any existing handlebar ends and, if necessary, instruments to prevent scratching during the assembly.
3.
The old handlebar grips are removed as follows:
3.1
Use a screwdriver to lift up the end of the grip and squirt some detergent solution under the grips. Alternatively, brake cleaner can be used for rubber grips (rubber grip only). If you no longer want to use the old grips, you
can cut them open with a knife. It is essential to ensure that the rotary gas sleeve is not damaged, as it is usually made of thin plastic.
3.2
Carefully slide the grip off the handlebars.
4.
It is easiest to assemble with the grips warmed up. Soak the grips in a lukewarm water / detergent solution for a few minutes.
CAUTION
: Since the detergent solution is evaporating very slowly, the full grip of the grips on the
handlebars is reached after 24 hours at the earliest. Alternatively, brake cleaner can be used to make it easier to slide the grips onto the handlebars. The turned aluminium parts remain on the grip during the installation (Fig.2)!
5.
Note the different inside diameters of the grips (Fig.1).
6.
Fit any previously removed instruments or handlebar ends.
7.
CAUTION:
It is essential to check that the grips on the handlebars and the throttle sleeve are securely attached! The throttle tube can be rotated freely and must immediately and independently return to the idle position when the
grip is released. Neither the instruments nor the handlebar ends slow down the rotation of the grip!
8.
CAUTION
: A jammed throttle affects driving safety!
Find suitable housings, turn signals, taillights, power resistors, electronic flasher relays, adapter cables and other accessories in our Webshop!
Exclusion of liability and warranty regulation:
Improper handling, installation or use of the device may invalidate warranty and warranty claims. Due to the non-verifiability of the proper application, the company Paaschburg and Wunderlich GmbH assumes no liability for direct or indirect damage or consequential damage resulting from the operation of the device. This
does not apply if the damage is due to intent or gross negligence of Paaschburg & Wunderlich GmbH or the damage consists of injury to life, limb or health or Paaschburg & Wunderlich GmbH has culpably violated an essential contractual obligation (cardinal obligation).
Paaschburg & Wunderlich GmbH, Am Alten Lokschuppen 10a, D-21509 Glinde
Tel.: +49 (0) 40 248 277-0; E-Mail:
All rights reserved. Changes and errors are excepted.
138-NO132A_Rev00_2020-11
Before each ride: It is the duty and responsibility of the rider to regularly check and maintain the safety-related vehicle parts. Before starting your journey, check the correct adjustment and function of the LSL
products and the tightness of all screwed connections.
Warranty: Take the time to do a 100% professional job of installing the LSL products. Take into account all our installation and safety instructions.
A faulty, improper installation or handling of the product will void the warranty.
Maintenance/Care: Do not use aggressive detergents to care for the LSL products. The LSL products can be perfectly cleaned with a simple, lukewarm detergent solution. Contact with brake fluid, brake cleaner,
fuel, etc. should be avoided. Immediately pick up any unintentionally applied impurities with a soft cloth and clean the surface with detergent solution
Enviromental Information: This LSL product may not be disposed in the normal household rubbish at the end of its lifetime. The disposal can be done through the Paaschburg u. Wunderlich customer service
or a local return and waste collection institution.
A = Ø 34 mm
B = 132 mm
A
B
Fig. 2
Fig. 1
