background image

620J Storage Enclosure Installation and Overview Guide

FCC-1

Regulatory Compliance Statements

FCC Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) 
Rules. These limits are designed to provide reasonable protection against harmful 
interference in a commercial installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. Operation of 
this equipment in a residential area is likely to cause harmful interference, in which case 
the user will be required to correct the interference at his/her own expense.

LSI Corporation, is not responsible for any radio or television interference caused by 
unauthorized modification of this equipment or the substitution or attachment of 
connecting cables and equipment other than those specified by LSI. It is the user’s 
responsibility to correct interference caused by such unauthorized modification, 
substitution, or attachment.

This Class A digital apparatus meets all requirements of the Canadian 
Interference-Causing Equipment Regulations.

Cet appareil numérique de la classé A respecte toutes les exigences du 
Règlement sure le matèriel brouilleur du Canada. 

Содержание 620J















































Отзывы: