manualshive.com logo in svg

LS RS485/Modbus-RTU, Руководство пользователя

Поделиться
Скачать
LS RS485/Modbus-RTU Скачать руководство пользователя страница 12

 

11

0x06 

Preset Single Register 

0x10 

Preset Multiple Register 

 

5.2.2. Exception code 

Exception code 

Description

 

0x01 

ILLEGAL  FUNCTION 

0x02 

ILLEGAL  DATA  ADDRESS 

0x03 

ILLEGAL  DATA  VALUE 

0x06 

SLAVE  DEVICE  BUSY 

User 

define 

0x14 

1. Write Disable (Address 0x0004 value is 0). 
2. Read Only or Not Program during Running. 

 
5.3. 

5.4. 

6. 

Baud Rate 

1200, 2400, 4800, 9600, 19200, 38400 bps (Default value: 9600bps) 

 

Broadcast Function 

z

  The broadcast function is used when Command is given to all inverters connected to network. 

z

  In the case of RS485, all inverters run without response (Slave->Master) when Command is given 

to Inverter Number 255(0xFF). 

z

  In the case of Modbus-RTU, all inverters run without response (Slave->Master) when Command is 

given to Inverter Number 0(0x00). 

 

TROUBLE 

SHOOTING 

Refer to this chapter when occurring problem in communication with computer while using this option 

card. 

z

  CPU LED malfunction 

Expected 

State 

The inverter is not working normally or the inverter and the option card are not 
connected properly. 

Corrective 

Measures 

1. Verify the power is applied to the inverter. 
2. Verify the option card is installed properly within the inverter when the inverter 
is working normally. 

z

  RXD and TXD LEDs malfunction 

Check Points 

Corrective Measures 

Is the power applied to the converter? 

Apply power to the converter. 

Is the connection between the converter and computer correct?

Refer to the converter manual

Is the communication card installed within the inverter properly? Refer to “4 Installation”. 
Does Master start the communication? 

Start the communication. 

Is the communication speed setting of the inverter correct? 

Refer to “4 Installation”. 

Is the data format of User program correct? 

Modify User program 

note4).

Is the connection between the converter and the option card 
correct? 

Refer to “4. Installation”. 

note4)

 User program is User-made S/W for PC. 

z

  ERR LED is working 

State 

Corrective Measures 

Blinking intermittently 

In case that the option card is receiving wrong data due to Noise or 
other causes. It is normal. 

Содержание RS485/Modbus-RTU


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды