LP Morgan Rondo Opus Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 20

LP Morgan Rondo Opus Скачать руководство пользователя страница 2

2 | LP Morgan Installation Instructions

LP Morgan Rondo Opus Manual

Table of contents

To the owner

2

Rondo Precision Drive parts supplied

3

Rondo Standard Motorised parts supplied

4

Rondo CC EasyFit parts supplied

5

Rondo IR (Infra-Red) EasyFit parts supplied

5

Wall mounting the screen - for all screens

6

Ceiling mounting the screen - for all screens

7

Concealed mounting - pelmet mounted
reverse wound screen

8

Electrical installation - Standard Motorised screens

9

Height adjustment - Standard Motorised screens

10

Electrical installation - CC EasyFit screen

11

Electrical installation - IR EasyFit screen

12

Limit setting - CC & IR EasyFit screens

13

Troubleshooting

14

Using Your Screen - Precision Drive

15

Maintenance - for all screens

16

Extras and accessories

17

Warranty information

18

Information in this document is subject to change without notice.
© Herma Technologies. All rights reserved.
This document is protected against unauthorised copying electronic or otherwise.

Trademarks used in this text: Herma, the Herma Logo, Galleria, LP Morgan and
LP Morgan logo are registered trademarks of Herma Technologies.
Other trademarks and trade names used in this document remain the property
of the relevant owners.

March 2012 Version 9.2

«
1
2
3
4
...
»

Содержание Rondo Opus





















Отзывы:

Нет отзывов