Lowrance HDS Live Скачать руководство пользователя страница 44

Страница: 44 / 70

Recommended action:

•

Disconnect the Helm-1 and verify that the alarm disappears.

•

Check resistance of the clutch coil equals 16 ohms (pin 1 and 2 in
connector).

No rudder response (For Helm-1/cable steer only)

Probable cause: No response to rudder commands.
Recommended action:

•

Check the cable connections between NAC-1 and Helm-1.

•

Check the Rudder FB potentiometer in Helm-1.

•

Check the Helm-1 drive motor.

Rudder drive overload

Probable cause: The drive unit shuts down due to an excessive load
or a short circuit.
Recommended action:

•

Check the drive unit and drive unit installation.

•

Look for mechanical obstructions.

•

Check the manual steering.

High drive temp*

Probable cause: The NAC-1 drive output circuit is overheated due to
excessive load.
Recommended action:

•

Switch the Autopilot to Standby.

•

Check the drive unit (see “Rudder drive overload”).

Drive inhibit*

Probable cause: There is an internal NAC-1 failure causing the drive
output circuit to shut down.
Recommended action: Contact support.

Low CAN bus voltage

Probable cause: The CAN bus voltage is less than 9V.
Recommended action:

•

Check cabling.

•

Check battery condition.

•

Check charging voltage.

Software setup

| HDS Live Installation Manual

Содержание HDS Live







































































Результаты поиска

Содержание HDS Live

Отзывы:

Похожие инструкции для HDS Live

Бренды по названию

Популярные бренды

Lowrance HDS Live, Руководство по установке

Результаты поиска

Содержание HDS Live

Отзывы:

Похожие инструкции для HDS Live

Бренды по названию

Популярные бренды