background image

Lowell Manufacturing Company

• 100 Integram Drive • Pacific, Missouri 63069 U.S.A.

Call

800.325.9660, 636.257.3400 • 

Fax

636.257.6606 • 

Click

www.lowellmfg.com

Lowell makes every effort to provide accurate information and reserves the right to change specifications and/or improve manufacturing methods. 

Download and print this spec from www.lowellmfg.com to insure that you have the most current information

1c-107

pg 3 of 4

ACSP2004-IG-GTF

20A Single-circuit Surge Suppressor with Ground Transient Filter

ACSP2004-IG-GTF Installation to Rack Mounting Rail Supports

1) Remove 1/4”

knockouts from
chassis base.

2) Loosely install

1/4-20 bolts
and slide nuts.

3) Attach to slide channel

in mounting rail support
and tighten bolts.

Specifications

Surge Suppressor
Operating Voltage

0-130 VAC nominal

Operating Current

20A hardwired, 16A w/receptacles(s) per NEC
210.21(B)(2), 210.23(A)(1).

Maximum Surge Current

72,000A (exceeds UL1449-2 6000V, 3000A).

Initial Clamping Voltage

205V, UL rating 330V

Endurance

IEEE C62.41-1991, B3 (C1), Pulses (lifetime):

1kv≥1,000,000; 3kv≥100,000; 6kv≥5000

Transient Noise Reduction 25dB@100kHz, 50dB@1MHz
Response Time

Less than 5 nanoseconds

Protection Mode

Line to neutral, zero ground leakage

UL1449-2 Adjunct Results 1000 surges, 6000 volts, 3000A, C1 and B3

waveforms (IEEE C62.41), No failures

Federal GSA specs (1996) Grade A, Class 1, Mode 1
Diagnostic LED’s

Top (Green): On = Ground verified, 
Center (Green): On = Protection active, 
Bottom (Red): On = Protection reduced*.

Applicable Standards

IEEE standard 587-80 A & B, IEEE standard
C62.41-1991, IEC 1000-4-5-1995 (IEC 801-5).

Safety Agency Approvals Assembly is ETL Listed to UL1449 2nd

Edition; rev 2/2005 (US and Canada).

ACSP2004-IG-GTF Carton Contents

Blank Auxiliary

Cover IG Receptacle

(not installed)

Blank 

Cover

Mounting

and 

hook-up

hardware

IG Rece GTF filter
(factory installed)

Ground Transient Filter (GTF)
Operating Voltage

125 VAC 

Operating Current

20A 

Frequency

60Hz

Impedance@60Hz

0.06 Ohms

Applicable Standards

Electromagnetic Interference filters 

(ANSI/UL 1283 - 4th Edition, 6/1998; rev 2/2004), 
and (CSA C22.2 No. 8 - M1986). 

Mechanical
Dimensions

7”W x 8”H x 3”D

Weight

7 lbs.

Input Connections

Hardwired pigtail leads, 12 gauge minimum.

Output Connections

(2) Duplex receptacles mounted on 90

O

rotatable

plates or hardwire pigtail leads ( 2) blank 90

O

cover plates are included for hardwire use.

Chassis

Steel with black powder epoxy paint finish.

Mounting Options

Compact for rear rack installation to mounting
rail supports or solid surface using flanges.

*Lowell's Triple Clamping Redundancy is exactly that - triple clamping for triple protection. This
means that if one section of the suppressor has ‘reduced protection’, there are two additional
sections available to safeguard equipment. Device is endurance tested and verified: Grade A,
Class 1, Mode 1.

A & E Specifications

The 20A single circuit surge protection device shall be Lowell Model
ACSP2004IG-GTF with ground transient filter and (2) duplex isolated
ground outlets. The surge suppressor/ground filter assembly shall be ETL
listed (1449-2) and endurance tested to meet government GSA Grade -
Mode - Class requirements for surge suppressors. It shall meet ANSI
C62.41 and protect line to neutral without ground wire contamination. It
shall be capable of protecting audio, video, broadcast, computer, DSP,
sound recording and reinforcement equipment from transient voltages,
spikes and surges. It shall include Lowell’s Triple Clamping Redundancy

TM

(TCR) technology to defeat surges up to 72,000 amps and have a
response time of less than 5 nanoseconds. It shall include Transient Noise
Reduction (filtering) of 25dB@100kHz, 50dB@1MHz. 

Additionally, it shall include Lowell’s patented GTF ground filter technology
to attenuate high frequency transients. The filter shall be compliant with
the Standards for Electromagnetic Interference filters (ANSI/UL 1283 - 4th
Edition, 6/1998; rev 2/2004) and Electromagnetic Interference filters (CSA
C22.2 No. 8 - M1986). The filter shall have a current rating of 20A and
impedance of 0.06 ohms at 60Hz.

The assembly shall rack mount and include (2) duplex isolated ground
outlets mounted on 90º plates that can be rotated for front or side access
plus blank plates for hardwire applications.  The front shall include three
LED's for visual ground verification and diagnostics.

Отзывы: