background image

3

 

Important Safety Notices: 

 

Before installing operating or servicing this equipment read carefully 
and understand the following precautions: 

 

 

Never service the machine without completely removing all 
power sources first.  Refer to your company’s Lock out / Tag 
out procedures. 

 

 

Do not bypass or remove safety guards on the machine or 
tape cartridges. 

 

 

Do not override safety devices such as interlock safety 
switches if applicable. 

 

 

Never adjust the tape cartridges or machine when the 
machine is operating. 

 

 

Do not place hands or body inside confines of machine unless 
the top head assembly is locked in position and all power 
sources are locked out. 

 

 

Do not wear jewelry, loose clothing, such as ties scarves, etc 
and long hair should be pulled backed when operating this 
machine. 

 
 

 

Never pull jammed boxes out of an operating machine.  
Always remove all power sources first. 

 
 

 

When feeding boxes into a semi automatic machine always 
hold top flaps down at rear of box.  Never place hands near 
the top head assembly of the machine. 

 
 

Содержание LITTLE DAVID LD7D/3




























Отзывы: