LOTOS LTP7000 Скачать руководство пользователя

Страница: 8 / 18

v

REAR CONTROL PANEL

The unit is connected to the supply even if

the Power Switch is in the “OFF” position,

and therefore there are electrically live parts

inside the power source. Carefully follow the

instructions given in this manual.

REAR CONTROL PANEL

Power Cord

b Unit Power Switch

Cooling Fan

d Air Inlet / Air Hose Connection

Air Regulator Mounts

v

CONTROLS AND SETTINGS

CONTROLS & SETTINGS

1 Digital Display
2 Cutting/Gas Checking Switch

3 Warning Light

4 Current Adjust Knob
5 Ground

Cable&

Clamp

Connection (Electrode Positive)

6 Torch

Trigger

Control

Connection

7 Pilot Arc Connection
8 Torch

Power

Connection

(Electrode Negative)

The annotation will be used later in Installation section to avoid confusions.

Switch between Cutting mode and Gas Checking mode.

Warning light indicates over-current, over-heating or other electrical problems with the unit when the light is on.

Содержание LTP7000



















Результаты поиска

Содержание LTP7000

Отзывы:

Похожие инструкции для LTP7000

Бренды по названию

Популярные бренды

LOTOS LTP7000, Руководство пользователя

Результаты поиска

Содержание LTP7000

Отзывы:

Похожие инструкции для LTP7000

Бренды по названию

Популярные бренды