LOTOS LTP7000 Скачать руководство пользователя страница 6

Страница: 6 / 18

SPECIFICATIONS

v

GENERAL DESCRIPTION

The LOTOS LTP7000 IGBT Plasma Cutter is one of the most powerful inverter plasma cutters in the market.

The pilot arc feature is especially useful for continuous cutting on rough surfaces or dirty metal. It has been

redesigned to incorporate the latest high frequency inverter technology using V-MOSFETs, along with PWM

(Pulse Width Modulation), the combination of which help deliver a far more constant, concentrated and precise

current to the cutting surface. With this plasma cutter, the user can achieve smooth, clean and uniform cuts on

a wide range of surfaces with minimal heat input and without distortion of metal. It is very easy to use by the

DIY user, while fully accommodating the demands of professional operators.

ü

70-amp pilot arc plasma cutter

ü

Automatic dual frequency (50/60Hz)

ü

High frequency start and contact start hand torch

ü

Suitable for stainless steel, alloy steel, mild steel, copper and aluminum, etc.

v

WHAT’S INCLUDED

Ø

Power Supply

Ø

Plasma Cutting Torch

Ø

Plasma Cutting Consumables

Ø

Ground Clamp

Ø

Air Filter & Regulator

Ø

Air Hose

Ø

Air Hose Connections and Tools

Содержание LTP7000



















Результаты поиска

Содержание LTP7000

Отзывы:

Похожие инструкции для LTP7000

Бренды по названию

Популярные бренды

LOTOS LTP7000, Руководство пользователя

Результаты поиска

Содержание LTP7000

Отзывы:

Похожие инструкции для LTP7000

Бренды по названию

Популярные бренды