Lorenzo SMS17102, Инструкция по эксплуатации, Страница: 11 / 16

11 Lorenzo
• After switching on the saw, wait for the
blade (5) to reach its maximum speed.
• Press the release lever (1) sideways and,
using the handle (2), apply steady and
light downward pressure to move the
machine head through the workpiece.
• When the cut is completed, return the
machine to its top parking position and
let go of the ON/OFF switch.
Caution! A return spring causes the
machine head to rise automatically at the
end of the cut. Do not let go of the handle
(2) as soon as the cut is completed but
steady the machine head and allow it to
rise slowly.
3. Precision adjustment of the stop for
90° cross-cuts ( Fig.4, 5 )
• Lower the machine head (4) and fix with
the lock pin (16).
• Slacken the tightening screw (12).
• Place the stop angle (A) between the saw
blade (5) and rotary table (8).
• Slacken the counter nut (23) and adjust
the setting screw (24) until the angle
between the saw blade (5) and the rotary
table (8) equals 90°.
• Re-tighten the counter nut (23) to fix the
machine in this setting.
4. 90° cross-cuts and 0°-45° rotary table
( Fig.6 )
This machine can be used to make angled
cuts of 0°-45° relative to the stop rail on
the left and right side.
• Release the rotary table (8) by slackening
the locking handle (10) and pressing the
latch (11).
• Turn the rotary table (8) by its handle (2)
to the angle you want, i.e. the mark (a)
on the rotary table has to compy with
the required angle dimension (17) on the
base plate (9).
• Re-tighten the locking handle (10) in
order to fix the rotary table (8) in position.
• Make the cut as described in “Section 2”.
5. Mitre cuts 0°-45° and rotary table 0°
( Fig.4, 7 )
This machine can be used to make mitre
cuts of 0°-45° relative to the machine bed
on the left side.
• Lift the machine head (4) to its top
position.
• Fix the rotary table (8) in 0° position.
• Undo the tightening screw (12) and use
the handle (2) to tilt the machine head (4)
to the left until the pointer (a) coincides
with the required angle value (15).
• Re-tighten the locking nut (12) and make
the cut as described in “Section 2”.
6. Precision adjustment of the stop for
45° mitre cuts ( Fig.8, 9 )
• Lower the machine head (4) and fix with
the lock pin (16).
• Fix the rotary table (8) in 0° position.
• Undo the tightening screw (12) and use
the handle (2) to tilt the machine head (4)
to the left until it coincides at 45°.
• Place the 45° stop angle (A) between the
saw blade (5) and the rotary table (8).
• Slacken the counter nut (5) and adjust the
setting screw (26) until the angle between
the saw (5) and the rotary table (8) equals
exactly 45°.
7. Mitre cuts 0°-45° and rotary table 0°-
45° ( Fig.10 )
This machine can be used to make mitre
cuts of 0°-45° relative to the machine bed
on the left side.
• Lift the machine head (4) to its top
position.
• Undo the rotary table (8) by slackening
the locking handle (10) and pressing the
latch (11).
• Adjust the rotary table (8) by its handle (2)
to the required angle (See also “Section 4”).
• Retighten the tightening screw (10) in
order to secure the tumtable in place.