LORD 6253-4220 Скачать руководство пользователя страница 40

Страница: 40 / 75

3DM

-GX5-25

User Manual

5.6.1

Bias Convergence

Accurate estimation of the biases can take several minutes to converge, therefore after the filter is

initialized, the free-inertial performance will continue to improve until the bias estimations settles.

The MEMS sensor manufacturers quote bias drift stability numbers which correspond to the

expected drift in bias while the sensor is operating. The filter attempts to track the changing biases

over time, and a user can expect these bias estimates will be non-constant during a navigation run.

5.7

Adaptive Anomaly Rejection

5.7.1

Gravity Adaptive

Enabling this feature allows the filter to stabilize attitude readings when undergoing linear

accelerations. The bandwidth setting determines the cutoff frequency of the filter applied to linear

acceleration changes (

see Communications Bandwidth on page 42

). The high and low limits

determine the trigger points at which the stabilization is applied. The limit values are in

meters/second² and the bandwidth is in Hz. To find this setting, select the sensor name and then

Settings > Device > Estimation Filter > Gravity Adaptive.

Manual Adaptive (default setting): Enter user-set fixed values.

Auto-Adaptive: Automatically estimates the values internally.

Figure 31 - Gravity Adaptive Settings

Содержание 6253-4220












































































Результаты поиска

Содержание 6253-4220

Отзывы:

Бренды по названию

Популярные бренды

LORD 6253-4220, Руководство пользователя

Результаты поиска

Содержание 6253-4220

Отзывы:

Бренды по названию

Популярные бренды