LORCH X 350 Скачать руководство пользователя

Страница: 8 / 40

Before start-up

- 8 -

11.18

909.1550.1-08

Connecting the inert gas cylinder

Abb. 4: Gas connection

Place the inert gas cylinder 28 in a suitable location

and secure to prevent it from falling over.

The cylinder can be secured using a wall bracket or

cylinder trolley.

Briefly open the gas cylinder valve 27 several times in

order to blow out any dirt particles that are present.

Connect the pressure reducer 22 to the inert gas cyl-

inder 28.

Screw the inert gas hose 24 to pressure reducer 22

and open the gas cylinder valve 27.

Setting the inert gas quantity

Open the valve 19 on the TIG welding torch.

Inert gas flows out.

The flow meter 23 indicates the gas quantity, and

the content pressure gauge 26 indicates the cylinder

content.

Close the valve 19 on the TIG welding torch when the

torch is not being used in order to prevent unneces-

sary use of gas.

11.3 Electrode welding process
Connecting the electrode welding cable

Connect the electrode welding cable to the minus

or plus socket 8 and secure the cable by rotating it

clockwise.

The polarity of the electrode depends on

the type of electrode and the welding proc-

ess. Please follow the manufacturer's in-

structions on the electrode packaging for

this purpose.

11.4 TIG welding process

For TIG welding you require a TIG valve

torch (Type LTV2600) for this device

Installing electrodes

Unscrew the clamping cap 17.

Remove the electrode 16 from the collet 18.

Grind the end of the electrode 16.

Slide the electrode 16 into the collet 18.

Insert the electrode 16 into the torch and firmly tight

en the clamping cap 17.

Do not dismantle the collet body 20 and the

gas nozzle 21.

When converting the torch to a different

electrode diameter, please pay attention to

the following.

The collet 18, collet body 20 and electrode 16 must

have the same diameter.

The gas nozzle 21 must be matched to the electrode

diameter.

Connecting the TIG torch

Connect the TIG torch to the minus 8 connection

socket and secure it by turning it clockwise.

Содержание X 350









































Результаты поиска

Содержание X 350

Отзывы:

Похожие инструкции для X 350

Бренды по названию

Популярные бренды

LORCH X 350, Руководство по эксплуатации

Результаты поиска

Содержание X 350

Отзывы:

Похожие инструкции для X 350

Бренды по названию

Популярные бренды