LORCH ControlPro T 180 AC/DC, Руководство по эксплуатации

Страница: 46 / 282

Starting up
- 46 -
04.19 909.1709.9-05
14.5 User-specific menu
Â
Switch off the equipment at the main switch 10.
Â
Press the selection button on the left 32 and keep it
depressed.
Â
Switch on the equipment at the main switch 10
9
The user-specific menu is activated. The menu item
is shown in the 7-segment display 36.
9
The set value is shown in the 7-segment display 35.
Â
Press the selection button 32 or 33 to switch among
the menu items.
Â
Turn the control dial 34 to change the set value.
Menu
no.
Menu item
Setting
values
C00 Display and adjustment of the torch-ID.
See „Adjustment of the torch-ID“ on page
46.
9...45
C01 Welding current limit for up/down torch.
When the welding current limit is switched
to “On”, the welding current on the up/down
torch cannot be set higher than pre-select-
ed on the control terminal.
On-Off
C02 Deactivation of the error message E05-00
(water pump) and of the water cooling unit
by LorchNet.
If the deactivation is switched “on”, the
error message E05-00 (water pump) is no
longer displayed.
Also the water cooling unit is not switched
on by LorchNet.
Practical, e.g. for the use of an automatic
torch without plug or a cooling unit without
LorchNet.
On-Off
C03 Activation of the orbital welding mode. On-Off
C04 ON: at short circuit the welding current
don’t increase the adjusted welding current
shown in the display (set value).
Off: at short circuit the welding current is
increased on minimum 60 A.
On-Off
C05 ON: by quick pressing of torch button 1
(start / stop) the 2nd torch button is simu-
lated.
(Second current on / off). Useful e.g. for
torches with one button only.
On-Off
C06 ON: the current decrease (downslope) will
be - as adjusted – conducted, also if the
torch button is released (4th tact).
Off: at earlier release of the torch button
(4th tact) the current decrease (downslope)
is interrupted.
On-Off
C07 On: PE conductor monitoring activated
Off: PE conductor monitoring deactivated
the PE conductor monitoring is an optional
available feature
On-Off
Menu
no.
Menu item
Setting
values
C08 Off: Using a foot remote control, the mini-
mum current (independent from the adjust-
ed welding current) in the TIG mode / AC at
electrode-Ø 1,0...2,0 mm = 10 Amps
electrode -Ø 2,4 mm = 15 Amps
electrode -Ø 3,2 mm = 20 Amps
On: the increased minimum current in the
TIG-mode / AC is deactivated
On-Off
C10 Welding current limit
0 = Off
I1
Min
...I1
Max
= On
0,
I1
Min
...
I1
Max
Tab. 6: User-specific menu
Â
Switch the equipment off at the main switch 10 to
transfer the settings from the user-specific menu.
Adjustment of the torch-ID
Every torch of the i-LTG/i-LTW-series has an own torch-
ID. This ID is related to the stress limits of the torch. If
the torch protection is activated (sub-parameter “tPr” =
on) in the TIG-mode, only a welding current according to
the maximum torch limit can be adjusted at the welding
machine.
‰
The adjustment of the torch –ID is necessary for e.g.
if the torch pc-board was changed.
Â
Select in the user specific menu code-no. C00
Â
Adjust the required torch-ID at the turning knob 34,
according to the torch-ID-chart.
Type of torch Torch-ID
Stress limits
DC AC
i-LTG 900 9 125 A 80 A
i-LTG 1700 17 150 A 120 A
i-LTG 2600 26 200 A 160 A
i-LTG 2800 28 300 A 250 A
i-LTW 3000 30 320 A 220 A
i-LTW 1800 18 350 A 250 A
i-LTW 1800sc 19 400 A 320 A
i-LTW 2000 20 220 A 165 A
i-LTW 4500 45 450 A 360 A
Tab. 7: Torch-ID
Â
Press button „Save 58“ to save.
9
The adjusted torch-ID is transferred to the torch.
14.6 Other welding processes
MACS
1, 3
With the MACS (Modulated AC system) welding proce-
dure, the welding current is pulsed with alternating and
direct current.
Â
Select the desired mode with button 20.