Loopcomm LP-7665 Скачать руководство пользователя | Manualshive

Страница: 37 / 55

background image

Describe "WPS Status Bar" - "PIN - xxx" as follow:

Acceptable PIN Configurations:

Start PIN connection - SSID ~> Begin associating to WPS AP ~> Associated to WPS AP ~> Sending
EAPOL-Start ~> Sending EAP-Rsp (ID) ~> Receive EAP-Req(Start) ~> Sending M1 ~> Received M2
~> (Received M2D ~> Sending EAP-Rsp(ACK)) ~> Sending M3 ~> Received M4 ~> Sending M5 ~>
Received M6 ~>Sending M7 ~> Received M8 ~> Sending EAP-Rsp(Done) ~> Configured ~> WPS
status is disconnected ~> WPS status is connected successfully-SSID

WPS configuration doesn't complete after a

two-minute connection

:

WPS EAP process failed.

When errors occur within

two minutes of connecting

, the WPS status bar might report "WPS EAP

process failed".

Error messages might be:

1. Receive EAP with wrong NONCE.

2. Receive EAP without integrity.

3. Error PIN Code.

4. An inappropriate EAP-FAIL received.

4.2.7.4 Example to Add to Registrar Using PBC Method

The PBC method requires the user to press a PBC button on both the Enrollee and the Registrar within
a two-minute interval called the Walk Time. If there is only one Registrar in PBC mode, the PBC mode
selected is obtained from ID 0x0004, and is found after a complete scan. The Enrollee can then
immediately begin running the Registration Protocol.

If the Enrollee discovers more than one Registrar in PBC mode, it MUST abort its connection attempt
at this scan and continue searching until the two-minute timeout.

*Before you press PBC on STA and candidate AP. Make sure all APs aren't PBC mode or APs using
PBC mode have left their Walk Time.

1. Select

Enrollee

from the Config Mode drop-down list.

37

«
...
35
36
37
38
39
...
»

Содержание LP-7665
























































Отзывы:

Нет отзывов

Похожие инструкции для LP-7665

Бренд: Queclink Страницы: 10

5.1 Channel Surround Sound Card ENM232-6VIA

Бренд: Encore Страницы: 2

Icy Box IB-PCI1901-C32

Бренд: RaidSonic Страницы: 16

Бренд: Fusion Страницы: 126

Obid ID RWA02.ABC-A

Бренд: Feig Electronic Страницы: 36

Бренд: ICP Electronics Страницы: 35

Бренд: DAT Страницы: 3

Бренд: Nvidia Страницы: 5

73-30130-01029-1

Бренд: Kvaser Страницы: 17

Бренд: Lindy Страницы: 2

ThinkStation NVS 315

Бренд: Lenovo Страницы: 30

Бренд: Lenovo Страницы: 30

AMD 7450 DP DVI-I

Бренд: Lenovo Страницы: 30

Бренд: IDTECH Страницы: 13

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

FZ-VNF551 Series

Бренд: Panasonic Страницы: 6

FZ-VDM551 Series

Бренд: Panasonic Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды