Loopcomm LP-7615 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 104

Loopcomm LP-7615 Скачать руководство пользователя страница 4

-4-

1

Introduction

1.1

Welcome

PCI Adapter connects you with IEEE802.11n(Draft 2.0) networks at receiving rate up to an incredible

15

0Mbps! By using the reflection signal, 802.11n

technology

increases the range and reduces

“dead

spots” in the wireless coverage area. Unlike ordinary

wireless networking of 802.11b/g standards that are confused by wireless reflections,

802.11n

can

actually use these reflections to increase four times transmission range of 802.11g products.
Besides, when both ends of the wireless link are 802.11n products,

The PCI

can utilize

twice radio band to increase three times transmission speed of ordinary 802.11g standard products,
and can comply with backwards 802.11b/802.11g standards.
Soft AP supported

by PCI Adapter can help you establish wireless LAN networking with lowest cost.

Besides, WPS

(PBC and PIN) encryption method can free you from remembering the long passwords.

Complete

WMM function makes your voice and video more smooth.

1.2

Product Feature

•

Complies with IEEE 802.11n (Draft 2.0), IEEE 802.11g, IEEE 802.11b standards

•

Provides 32-bit PCI interface

•

Provides

15

0Mbps receiving rate and

150

Mbps sending rate

•

Supports 20MHz/40MHz frequency width

•

Auto-detects and changes the network transmission rate

•

Provides two work modes: Infrastructure and Ad-Hoc

•

Supports Soft AP to establish your wireless LAN networking with lowest cost

•

Supports 64/128-bit WEP, WPA, WPA2 encryption methods and 802.1x security authentication
standard

•

Supports WPS (PBC and PIN) encryption method to free you from remembering long passwords

•

Supports WMM to make your voice and video more smooth

•

Supports Windows® 2000, XP 32/64, Vista 32/64

, Win 7 32/64

1.3

Contents of Package

•

One PCI Adapter

•

One Installation CD w/User Manual

•

One

dipole antennas

Contact your local authorized reseller or the store purchased from for any items damaged and/or
missing.

1.4

Before you begin

•

You must have the following:

•

A desktop PC with an available 32-bit PCI slot

•

Minimum 300MHz processor and 32MB memory

•

Windows 2000, XP, 2003, Vista

,Win7

•

A CD-ROM Drive

•

PCI controller properly installed and working in the desktop PC

•

802.11n or 802.11b/g Access Point (for infrastructure Mode) or another 802.11n or 802.11b/g
wireless adapter (for Ad-Hoc; Peer-to-Peer networking mode.)

«
...
2
3
4
5
6
...
»

Содержание LP-7615









































































































Отзывы:

Нет отзывов