Loopcomm LP-7615 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 104

Loopcomm LP-7615 Скачать руководство пользователя страница 33

Utility Config

-33-

: Indicates 802.11g wireless mode.

: Indicates 802.11n wireless mode.

: Indicates

that the AP list is sorted by SSID, Channel or Signal.

: Button to connect to the selected network.

: Issues a rescan command to the wireless NIC to update

information on the surrounding wireless network.

: Adds the selected AP to the Profile setting. It will bring up a

profile page and save the user's setting to a new profile.

: Shows the Status Section.

: Hides the Status Section.

Connected network :

When RaUI first runs, it will select the best AP to connect to automatically.

If the user wants to use another AP, they can click "Connect" for the intended

AP to make a connection.

If the intended network uses encryption other than "Not Use," RaUI will bring up

the security page and let the user input the appropriate information to make the
connection. Please refer to the example on how to fill in the security information.

When you double click an AP, you can see detailed information about that AP.

The detailed AP information is divided into three parts. They are General, WPS,
CCX information and 802.11n (The 802.11n button only exists for APs supporting N
mode.) The introduction is as follows:

General information contains the AP's SSID, MAC address, authentication type,

encryption type, channel, network type, beacon interval, signal strength and
supported rates. It is shown in Figure 2-3-1-2.

«
...
31
32
33
34
35
...
»

Содержание LP-7615









































































































Отзывы:

Нет отзывов