Chapter 6 Appendix A
6-12
If the specif ied f irm ware is downloaded successfully, the words “check sum ok”
will appear on your screen. For dem onstration purpose, those words are
highlighted on the sam ple screen below. Press ESC
V 4 1 0 0 = = = D o w n l o a d F i r m w a r e = = = 1 0 : 2 4 : 2 3 0 4 / 1 7 / 2 0 0 3
A R R O W K E Y S : C U R S O R M O V E , B A C K S P A C E t o e d i t , E S C t o a b o r t
F i r m w a r e 1 V e r s i o n : V 1 . 0 4 0 4 / 1 4 / 2 0 0 3
F i r m w a r e 2 V e r s i o n : S 1 . B 4 0 4 / 0 2 / 2 0 0 3
C u r r e n t F i r m w a r e B a n k : 1
N e x t B o o t F i r m w a r e : 1
T F T P S e r v e r I P : 1 9 2 . 1 6 8 . 1 0 0 . 2 0 6
F i r m w a r e F i l e N a m e : v 1 0 4 . r u n
1 0 : 3 3 : 2 4 0 4 / 1 7 / 0 3 D o w n l o a d i n g f i r m w a r e . . . R e c e i v e d 1 5 5 6 B l o c k s
1 0 : 3 4 : 3 3 0 4 / 1 7 / 0 3 c h e c k s u m o k
1 0 : 3 4 : 3 3 0 4 / 1 7 / 0 3 N e x t b o o t f i r m w a r e s w i t c h t o b a n k 2 .
1 0 : 3 4 : 3 3 0 4 / 1 7 / 0 3 R e c e i v e d 7 9 6 7 5 0 b y t e s i n 7 0 s e c o n d s
< < P r e s s E S C k e y t o c o n t i n u e > >
Note:
In the above screen you will notice the words ”
N ext b oo t
f i r mw a re sw i tc h t o b a nk 2 ”
.
When new firmware is downloaded to a Loop-V
4100 that has its current firmware in BANK 1, the new firmware is not activated until the Loop-
V 4100 is rebooted. Upon reboot the newly downloaded firmware will automatically be
switched to BANK 2 and it will become the new current firmware, Similarly, if the current
firmware is in BANK 2, the newly downloaded firmware will be switched to BANK 1 upon
rebooting. BANKS only switch after a download occurs and the Loop-V 4100 is rebooted.
After the downloading is successfully completed and a reboot takes place, the newly
downloaded firmware will be called the current firmware. The previous firmware will be stored
in the other BANK for backup. If a download fails and the user wishes to revert to the
previous firmware, instructions for doing so can be found in Section 6.2 of this appendix.
You must now reset the Loop-V 4100. When you do the firmware will switch from Bank 1 to
Bank 2.
Press Z from the Controller Menu. Use the arrow keys to move the asterisk to Primary. Then
press ENTER.
A prompt will ask “Are you sure?” (Y/N). Press Y. The download process is now complete
V 4 1 0 0 = = = C o n t r o l l e r M e n u = = = 1 4 : 1 7 : 1 3 0 4 / 1 8 / 2 0 0 3
S e r i a l N u m b e r : 0 2 4 0 1 7 C o n n e c t P o r t : S U P V _ P O R T
H a r d w a r e V e r s i o n : C S t a r t T i m e : 1 0 : 5 3 : 5 4 0 4 / 1 8 / 2 0 0 3
S o f t w a r e V e r s i o n : V 1 . 0 4 0 4 / 1 4 / 2 0 0 3 R e d u n d a n t C o n t r o l l e r : D i s a b l e d
[ D I S P L A Y ] [ S E T U P ]
C - > S y s t e m C o n f i g u r a t i o n S - > S y s t e m S e t u p
Q - > A l a r m Q u e u e S u m m a r y P - > P a s s w o r d S e t u p
I - > I n f o r m a t i o n S u m m a r y M - > S y s t e m A l a r m S e t u p
L - > F i l e T r a n s f e r
V - > S t o r e / R e t r i e v e C o n f i g u r a t i o n
B - > U n i t C o n f i g u r a t i o n C o p y
[ L O G ] [ M I S C ]
H - > C h o o s e a U n i t A - > A l a r m C u t O f f
F - > L o g O f f [ S E T U P ] , [ M I S C ] M e n u X - > C l e a r A l a r m Q u e u e
O - > L o g O n [ S E T U P ] , [ M I S C ] M e n u Y - > C o n t r o l l e r R e t u r n t o D e f a u l t
Z - > C o n t r o l l e r R e s e t
K - > L o a d A l l P o r t s D e f a u l t
R e s e t - a r e y o u s u r e ? [ Y / N ]