INTRODUCTION
Congratulations on your purchase of this product.
This User Guide suits
LBH36SFP
product. We adopt the
latest CMOS technical of sensor and driver. The most at-
tractive characteristics are small and easy hidden, suits
the elevator and corridor. In addition, it owns the charac-
ters of high
definition and stability, strong anti-jamming,
rich and real color. Fixing and
using this model are con-
venient too. It is very good for you to apply to your CCTV
system.
Please read this instruction manual carefully to en-
sure proper use of the product.
CONNECTING
BRIEF OF PRODUCT
*
Sensor
(
CMOS
)
Adopt SONY 1/3
"
CMOS Sensor.
*
Auto Gain Control (AGC)
Built-in auto gain control
(AGC)
circuit. The color camera
can get high definition picture in low Lux condition.
*
Scanning Mode
NTSC
or PAL
mode.
*
Water Resistance
IP66
*
OSD SETTING
DC12V
Power Supply
Monitor
LBH36SFP
TROUBLE AND SOLUTION
Link wire rule
：
Power
Video
Note
:
●
Please note the camera’s operating temperature and its using
environment
requirement. Avoid using the camera at too high
or too low temperatures. The operating temperature is
-
30~
+
60
℃
. (Recommendatory operating temperature is
-
10~+50
℃
.)
●
Never make the camera face the sun or bright object. Other-
wise, it will damage the CMOS
.
●
Do not mount the camera near by the radiator
or heater.
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole
whether exactitude
.
. Please check all the connecting cable and monitors whether be connected
correctly or not
.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply
.
. Check the monitor and peripheral equipments used.
3. The picture background color changes continuously
. The fluorescent lamp’s electromagnetic field cause color roll. This is proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
. The power supply’s voltage unstable
.
. Connecting cables not connect correctly or have high impedance.
The symbol is intended to alert the user to the presence of
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
uninsulated ‘dangerous voltage’ within the product’s
enclosure
that may be of sufficient Magnitude to
consti-
a risk of electric shock to persons.
Video
DC12V
CAUTION:
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK
DO NOT REMOVE COVER OR BACK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
MENU
UP
DOWN
RIGHT
LEFT
PRESS
KEY BOARD
OSD
SET
IMAGE
3D-NR
ON/OFF
AE MODE
INTELLIGENT/GLOBAL/CENTER/
CENTER WEIGHT/BLACK LIGHT/FRONT
LIGHT/DISTINGUISH
WB
AWB-PRO/AWB-TEMPORAL/AWB-AI/
AWB-GW/AWB-CCT
IMAGE ENHANCE SHARPNESS/CONTRAST/SATURATION
MIRROR
ON/OFF
FLIP
ON/OFF
BRIGHTNESS
0.10.20......250
ZOOM IN
0.1.2.3.4.5
DAY&NIGHT
EXTERNAL/COLOR/B&W/AUTO
ZONE
MASKING
COLOR
MOSAIC/WHITE/YELLOW/CYAN/
GREEN/MAGENTA/RED/BLUE/BLACK
AREA NO.0 - AREA NO.8
SENSITIVITY
AREA NO.0 - AREA NO.4
VIDEO
STANDARD
PAL/NTSC
LANGUAGE
CHINESE/ENGLISH
LOAD DEFAULT
SOFT VERION
SAVE&EXIT
EXIT
MOTION
DIRECTION
WEAK/LOW/MIDDLE/HIGH
