background image

Spinner Motorizer – User Manual 
 

 
The Spinner Motorizer is a device which allows you to motorize and remotely control your 
Spinner 360° camera. First you need to take your Lomography Spinner 360° camera (sold 
separately), simply attach the camera to the Motorizer Base, and press the remote control 
button for breathtaking and smooth photos - even at night or indoors! 
 
The device can also be used for experimenting with creative photographic techniques 
including time scans, endless images, or any other ways you can think of!

 

 
 

Attaching your Spinner 360° (sold separately) onto the Spinner Motorizer Base: 

 
Here’s how to detach the Spinner 360°’s handle: 
 
- Take your Spinner 360° camera (sold separately) 
- Loosen the rubber band 

<11>

 by pulling it off from the small pulley 

<12>.

 

- Detach the Spinner 360°’s core body from the handle by pulling them apart. 
 
Attaching the Spinner 360° body onto the Motorizer Base: 
 
- Place the rubber band around the motor pulley 

<2>

- Take the Spinner 360’s main body. Firstly fit the small pulley (under the body) 

<10>

 into 

the rubber band 

<11>

. Secondly, match the hole 

<12>

 with the brass connector 

<3>

 on the 

motor base, and then plug it in. 
 
 

Battery Supplies: 

 
Both the Spinner Motorizer Base and the Remote Control need batteries to work. The Spinner 
Motorizer Base needs at least 4 x AA batteries; the Spinner Remote needs 1xAA battery. 
 
 

Inserting Batteries into the Spinner Motorizer: 

 
- Turn the bottom cover 

<1>

 of Spinner Motorizer Base anti-clockwise to open the battery 

chamber. 
 
- You will see 4 cavities (in total 8 chambers) 

<4> 

where you can insert your AA batteries, 

with + /- signs indicating the correct battery installation position. Insert the batteries correctly 
according to the signs printed.   
 
- It's suggested that you install all 8 batteries to achieve the best stability and operation time.   
 
However the Spinner Motorizer Base also works with just 4 AA batteries. If you only have 4 
batteries, then install batteries into the four cavities separately. 
 
- Now you should match the white dot 

<5>

 on the bottom cover and the Motorizer Base, turn 

the bottom cover 

<1>

 clockwise to lock it again. 

Содержание Spinner Motorizer

Страница 1: ...Take the Spinner 360 s main body Firstly fit the small pulley under the body 10 into the rubber band 11 Secondly match the hole 12 with the brass connector 3 on the motor base and then plug it in Battery Supplies Both the Spinner Motorizer Base and the Remote Control need batteries to work The Spinner Motorizer Base needs at least 4 x AA batteries the Spinner Remote needs 1xAA battery Inserting Ba...

Страница 2: ...hould grab your film leader Take care that the Black Flap 17 stands like a wall between the Take Up Spool 16 and the Exposure Slit When everything is in place try to wind a little bit of the film with the Rear Door 13 still open by simply pressing the remote control button 8 while in continuous mode The film should feed correctly from the roll 4 Now close the Rear Door 13 and press the remote cont...

Страница 3: ...ND filter and place it in front of the Camera Lens 19 for best result Rewinding the Film 1 Switch the Aperture Setting 18 to R R stands for rewind mode 2 Detach the Rubber Band 11 from the camera Optional 3 Wind the Rewind Crank 15 clockwise until the pressure slackens Don t stop turning until you feel the tension completely drop off Only then you can make sure that your film is safely stored in i...

Страница 4: ...erence and 2 This device must accept any interference received including interference that may cause undesired operation 2 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Spinner 360 Motorizer 1 Motorizer Base Bottom Cover 2 Motor Pulley 3 Brass Connector 4 Motorizer Base 8 Battery Chambers 5 White Mar...

Отзывы: