Lombardini 3LD 450 Скачать руководство пользователя страница 31

Страница: 31 / 48

- 31 -

Workshop Manual_3 - 4 LD_cod. ED0053025560_

4° ed

_ rev.

Lubrication circuit

Oil pump

Make sure that the gear teeth are intact and check that the

clearance between the gear periphery and the pump case does

not exceed 0.15 mm and that the drive shaft can easily turn with

an axial clearance not exceeding 0.15 mm.

Check that the gear lubrication holes

and

are not clogged.

Tighten the pump case at 30 Nm.

Tighten the pump control gear at 20 Nm.

The oil pumps for 3LD 451/S and 3LD 510/S engines, which

turn anticlockwise (from flywheel position), are different, see

information below.

Oil pressure regulating valve

It is housed in the flywheel side main bearing

For 3LD 450, 3LD 451/S, 3LD 510, 3LD 510/S, see picture 63

Support

Sheet metal

Valve

Screw

Spring

Tighten the support at 25 Nm.

For 4LD 640, 4LD 705, 4LD 820,see picture 64

Support

Spring

Gasket

Flange

Valve support

Plate

Ball

Screw

Tighten the support at 40 Nm.

Oil filter cartridge

Componens:

Gasket

Bowl

Assembly

By-pass valve

Antidrainage rubber cap

Spring

Filter element

Features:

Maximum operating pressure: 7 bars

Maximum operating temperature: -25° + 150°C

Filtering degree: 20 µm

By-pass valve setting: 1÷ 1.4

Total filtering surface: 750 cm

Oil pump, difference between clockwise rotation pump and

anticlockwise pump

The difference between the oil pump on clockwise rotation

engines and the anticlockwise one is the suction duct provided

either with the pump case and with the base.

See picture 60 for anticlockwise rotation engines from flywheel

position (3LD 451/S, 3LD 510/S).

=Intake

= Delivery

Picture 61, for clockwise rotation engines, seen from the

flywheel side (3LD 450, 3LD 510, 4LD 640, 4LD 705, 4LD 820)

= Intake

= Delivery

Содержание 3LD 450

















































Результаты поиска

Содержание 3LD 450

Отзывы:

Похожие инструкции для 3LD 450

Бренды по названию

Популярные бренды

Lombardini 3LD 450, Руководство по ремонту

Результаты поиска

Содержание 3LD 450

Отзывы:

Похожие инструкции для 3LD 450

Бренды по названию

Популярные бренды