Lombardini 3LD 450 Скачать руководство пользователя страница 11

Страница: 11 / 48

- 11 -

3LD450 3LD510

Cm³

RPM

l/h

Kg/h

Kg.

l./1'

Kg.

454

18,1:1

3000

7,5

6,6

6,0

28,5

@ 1700

1,7

0.007

560

9000

250

35°

30°

****

510

18,1:1

3000

9,0

7,3

6,6

32,8

@ 1800

1,9

0.008

630

9000

250

35°

30°

****

4LD640 4LD705 4LD820

Cm³

RPM

l/h

Kg/h

Kg.

l./1'

Kg.

102

100

817

17,0:1

3000

11,4 D

10,3 D

@ 1600

3,0***

0,035***

105

890 D

10400 D

300

35°

25°

****

638

17,0:1

3000

10,5

8,8

7,9

38,7

@ 1700

2,4

0.024

100

780

12000

300

35°

25°

****

100

707

17,0:1

3000

12,0

9,9 D

8,8 D

43,1

@ 2000

2,6***

0,030***

100

770 D

10400 D

300

35°

25°

****

Workshop Manual_3 - 4 LD_cod. ED0053025560_

4° ed

_ rev.

Technical information

Cylinders

Bore

Stroke

Displacement

Compression ratio

rpm

N DIN 70020 - 80/1269/CEE - iso 1585

KW Power NB DIN 6271 - ISO 3046 - 1 IFN

NA DIN 6271 - ISO 3046 - 1 ICXN

Peak torque

Fuel specific consumption

Oil consumption

Dry weight

Combustion air volume at 3000 rpm

Cooling air volume at 3000 rpm

Max. axial load permissible for drive shaft in two directions

instantaneous

Max. inclination extended to 1 h.

permanent

It stands for power

It stands for NB power

***

It stands to NB power at 2600 rpm

****

According to the application D at 2600 rpm

Note:

For LDA 450, LDA 510, LDA 96, LDA 97, LDA 820 out-of-production engines, the repair specifi-

cations are equal to those of the engines specified in the table. 3 LD 451/S, 3LD 510/S engines,

which are currently produced, not specified in the table, turn anticlockwise ( seen from the flywhe-

el side), and are provided with the same feature as 3LD450 and 3LD510engines.

Cylinders

Bore

Stroke

Displacement

Compression ratio

rpm

N DIN 70020 - 80/1269/CEE - iso 1585

KW Power NB DIN 6271 - ISO 3046 - 1 IFN

NA DIN 6271 - ISO 3046 - 1 ICXN

Peak torque

Fuel specific consumption

Oil consumption

Dry weight

Combustion air volume at 3000 rpm

Cooling air volume at 3000 rpm

Max. axial load permissible for drive shaft in two directions

instantaneous

Max. inclination extended to 1 h.

permanent

ENGINE TYPE

Содержание 3LD 450

















































Результаты поиска

Содержание 3LD 450

Отзывы:

Похожие инструкции для 3LD 450

Бренды по названию

Популярные бренды

Lombardini 3LD 450, Руководство по ремонту

Результаты поиска

Содержание 3LD 450

Отзывы:

Похожие инструкции для 3LD 450

Бренды по названию

Популярные бренды