Page 2 of 2
USRIC USB Temperature Data Logger Quick Start Guide
5. LOGTAG
®
ONLINE
LogTag
®
Xpress and LogTag
®
Online are perfect companions for
uploading data from USRIC loggers, and viewing them in a web browser.
LogTag Xpress runs in the background and detects if loggers are plugged
into a USB port.
You can set up LogTag
®
Xpress (and also LogTag
®
Analyzer) so any files
downloaded from a USRIC USB logger are automatically uploaded to
LogTag
®
Online.
Customers can then simply type the logger’s serial number into the
Logger Transit Data on the LogTag
®
Online welcome page, and will be
able to view the data without the need to create an account
6. CALIBRATION
All LogTag
®
products can be calibrated and adjusted, using dedicated
utility software, which is made available to calibration laboratories on
request. If you regularly calibrate LogTag
®
data loggers, and think you
qualify, please contact
7. BATTERIES
When the software indicates that a logger’s battery is low,
the product has reached the end of its life.
The models listed in this guide each contain a non-
replaceable, non-rechargeable Lithium Battery, which must
be disposed of in accordance with local regulations.
Do not expose the logger to extreme temperatures as it may lead to the
destruction of the battery and may cause injuries.
Keep out of the reach of children.
8. WATER INGRESS
Please carefully observe the IP rating for your unit and remember that
none of the LogTag
®
products can be immersed into liquids.
9. USB CONNECTOR
Keep the USB connector free from moisture and contamination. Remove
the USB cap only when configuring or downloading the logger. It is
important that the cap is in place during the trip.
LIGHT PATTERNS
The following table shows how your LogTag USRIC indicates its operational status via the red and green LEDs.
Signal
Sequence
Occurrence
Wake-up signal
4 alternate flashes of green/red LED’s
• This is displayed after the configuration was successfully applied to the logger
• It is also shown when a logger is woken from hibernation.
Start-up signal
16 alternate flashes of green/red LED’s
• This is displayed when the logger starts its recording cycle.
Mark signal
5 simultaneous flashes of green/red
LED’s
• Displayed when pressing START/MARK button while recording to indicate an
inspection mark in the software.
• Displayed directly after the start-up signal following a push button start where
a recording delay has been configured. In this instance the start-up signal is
repeated when the actual recording begins.
Logging active, no
alert present
Single flash of green LED every 4
seconds
• Indicates the logger is recording.
• This is not displayed when pre-start is active and the main logging cycle has not
yet started. It is also not displayed when the green LED has been turned off in the
configuration screen.
Logging finished, no
alert present
Single flash of green LED every 8
seconds
• Indicates the logger has finished recording.
• This is not displayed when the green LED has been turned off in the configuration
screen. Will also be displayed when unit has been woken up from hibernation.
Logging active, alert
is present
Single flash of red LED every 4
seconds
• Displayed when the logger has been detected an alarm condition and the Alert
LED has been activated.
• If the Alert LED has not been activated during configuration, the green LED will
flash every 4 or 8 seconds as above.
Logging finished,
alert is present
Single flash of red LED every 8
seconds
• Indicates the logger has finished recording, and an alarm was triggered during the
trip.
Communication
The green LED flashes once a second
• During communication with the interface the green LED will flash.
Initiate Stop
14 simultaneous flashes of green/red
LED’s, followed by rapid flashing
• This LED sequence appears when the stop sequence is initiated and requires that
the STOP button is enabled during configuration of the logger.
• For the recorder to stop, the button must be released during the rapid flashing.
PDF generation
The green LED is permanently on
• This indicates the logger is processing the recorded data and will present a PDF
shortly, available through its on-board mass storage device.
Ready for re-flash
The red LED is on permanently
• The USRIC is ready to receive new firmware.
REV H 220116 - © Copyright 2022, LogTag North America Inc. All rights reserved.
10.
ACCESSORIES
Several accessories are available for your product, such as waterproof
enclosures and wall mount brackets.
Please enquire with your sales partner for more details.
11.
SUPPORT
If at any stage you feel you need further help, please contact your sales
partner or visit the LogTag support website at
http://logtagrecorders.com/support
•
