background image

14

INCH/MM

INCH

MM

The display can show measurment units in millimeters or 
inches. To select measurement unit, you press down the 
Inch/mm key.

If the saw blade position is raised 
from the set zero point, the value 
shown on the display is negative.

SAWING DIMENSIONS

The Smart Set interface initially shows the distance between 
the log bed and the bottom of the sawblade. The selected 
measurement is shown in the box called ABS on the display.

The Smart Set interface can show different sawing dimensions and 
units to facilitate for the user in different situations. The default 
setting of the interface is showing an absolute measurement between 
the sawblade and the log bed in millimetres.

1  2  3  4        A   B   C

ABS

10.00

100.00

10.00

TOE  BOARD

MM

REL

ABS

ABSOLUTE MEASUREMENTS

RELATIVE MEASUREMENTS

1  2  3  4        A   B   C

10.00

0.00

10.00

TOE  BOARD

MM

0

0

The 0 key creates a new zero point for the log bed position. From 
this zero point, a new relative measurement is shown for the posi-
tion of the log bed. If the sawblade is raised from this selected point, 
a negative value is shown, and if the sawblade is lowered a positive 
value is shown. On the display, the selected value is shown with the 
symbol 0. In this mode, the kerf is compensated manually.

0

FUNCTIONS

Содержание SMART SET

















Отзывы: