background image

13

6.0 Good service after purchase

6.1 Ordering spare parts

The correct spare parts are obtainable from your dealer.

When ordering, please state:

•   Serial number of the product

•   Type and width/length of the product

• 

Spare part no. Please find spare part no. on 

www.logitrans.com

.

6.2 Warranty/Compensation

Spare parts delivered during the warranty period will be invoiced. A credit note will 

be sent immediately after we have received and tested the defective parts and 

found that the warranty conditions have been met.

6.3 Service and repair

You should be able to make adjustments and perform minor repairs on the spot. 

However, major repairs should be left to the dealer who has well-trained personnel 

and the necessary special tools. 

6.4 Warranty

The warranty covers material and assembly defects which, subject to inspection by 

us or our representative, are deemed to be faults or deficiencies that prevent normal 

use of the parts concerned. Such affected parts shall be sent to your Logitrans 

 dealer carriage paid within the warranty period in force at the time in question, 

together with a copy of the documentation for the service performed (B284 - see the 

back page). The warranty does not cover normal wear and adjustments.  

The warranty period is based on singleshift working.

The warranty shall no longer apply if

•  the product has been used incorrectly,

•  the product is used in environments for which it was not designed,

•   the product has been overloaded,

•  replacements of parts have been made incorrectly or original parts have not been 

used and consequential damages have arisen,

•   if the product is changed or accessories, not being approved by Logitrans, are 

used,

• 

 it can not be proved that a qualified technician has performed the service check

-

according to the requirements stated in the instruction manual (see the back page). 

6.5 Liability exemption

The manufacturer accepts no responsibility for personal injury or material damage 

arising from deficiencies, defects or improper usage. The manufacturer accepts 

no responsibility for lost earnings, operating losses, lost time, lost profits or similar 

indirect losses incurred by the purchaser or a third party.

Содержание EHS 1000RF-SEMI

















Отзывы: