Logic IO RTCU LX5 pro Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 37

Logic IO RTCU LX5 pro Скачать руководство пользователя страница 8

RTCU LX5 pro Technical Manual V1.00

Advanced Industrial M2M/IoT Gateway

Logic IO ApS.

Ph: (+45) 7625 0210

Holmboes Allé 14

Fax: (+45) 7625 0211

8700 Horsens

Page 8 of 37

Email: [email protected]

Denmark

www.logicio.com

On the frontside of the device, the Ethernet, Communication, and Programming ports are found.
Also located on the front side is the Power and I/O connector.

Frontside

On the backside of the device, the LTE, WLAN, and GNSS antenna connectors are found. Also
located on this side is the small hole for the reset button.

Backside

Inside the encapsulation, the SIM-card / Micro SD-card readers and various
configuration/termination jumpers are located.

For convenience and easy installation, the front of the devices contains all connectors'
documentation and includes several tables for its layout.

LTE Antenna

Reset button

GNSS Antenna

WLAN Antenna

Power and I/O connector

Prog. port

Communication

port

Ethernet port

«
...
6
7
8
9
10
...
»

Содержание RTCU LX5 pro






































Отзывы:

Нет отзывов