manualshive.com logo in svg

Logic IO RTCU LX5 pro, Техническое руководство, Страница: 33 / 37

Поделиться
Скачать
Logic IO RTCU LX5 pro Скачать руководство пользователя страница 33

RTCU LX5 pro Technical Manual V1.00 

Advanced Industrial M2M/IoT Gateway 

 

Logic IO ApS. 

 

Ph:   (+45) 7625 0210 

Holmboes Allé 14 

 

Fax: (+45) 7625 0211 

8700 Horsens                               

Page 33 of 37 

Email: [email protected] 

Denmark                                       

 

www.logicio.com 

 

Appendix D 

–

 Device Configuration Guide 

Please refer to Appendix A to get inside access to the device. 

 
The RTCU LX5 pro has many features, and some of them require configuration by using hardware 
jumpers located inside the device. The placement of the jumpers are as follows: 
 

 

 
 

Feature 

Jumper 

State 

Default state 

Communication 

RS485 T. 

Installed 
Not installed 

RS485 line 

120 Ω resistor enabled

 

RS485 line 120 Ω resistor disabled

 

CAN T. 

Installed 
Not installed 

CAN bus line 120 Ω resistor enabled

 

CAN bus line 120 Ω resistor disabled

 

CAN WE 

Installed 
Not installed 

CAN bus write-enabled 
CAN bus write disabled 

Analog input 

Ain 1 

Installed 
Not installed 

Ain 1 current mode selected 
Ain 1 voltage mode selected 

Ain 2 

Installed 
Not installed 

Ain 2 current mode selected 
Ain 2 voltage mode selected 

Ain 3 

Installed 
Not installed 

Ain 3 current mode selected 
Ain 3 voltage mode selected 

RS485 line 
termination 

CAN bus 
 line termination 

CAN bus 
 write enable 

Analog input 
jumpers 

Ain 1 

Ain 2 

Ain 3 

Содержание RTCU LX5 pro






































Отзывы:

Нет отзывов