Logiblocs Super Inventor's Скачать руководство пользователя страница 46

Страница: 46 / 46

SAFETY ADVICE AND USEFUL TIPS

BETTER TO BE SAFE THAN SORRY !

Before you use the Logiblocs, be sure to read and understand this section on safety.

If used correctly, the Logiblocs are absolutely safe. The Logiblocs operate at
low voltage only.

Never connect any wires to mains electrical outlets.

BATTERIES - DOs and DON’Ts !

☛

Insert batteries according to +/- symbols.

☛

Only use the recommended batteries.
(4 x AA (LR6) 1.5V) and/or (1 x 9V 6F22 or 6 LR61)

☛

Do not use Nickel Cadmium rechargeable batteries.

☛

Replace all the batteries at the same time.

☛

Do not mix old and new batteries.

☛

Do not mix alkaline and standard carbon-zinc batteries.

☛

Do not attempt to recharge non-rechargeable batteries.

☛

Do not short-circuit the supply terminals or throw in fire.

☛

Remove batteries during long periods of non-use.

☛

Never leave worn out batteries connected – they might leak and corrode things.

☛

Use only one BATTERY BOX or BATTERY CONNECTOR in any circuit.

SOME MORE DOs AND DON’Ts

If you want to save the batteries, disconnect the BATTERY BOX when you finish a
Logibloc session. When using the BATTERY CONNECTOR (LBT/F2) just unplug it from
the other Logiblocs – there is no need to remove the battery from its tight connector.

Do not attempt to open up the Logiblocs.
Do not insert metal objects or wires into the connectors – this could
cause a short circuit !

Always plug together or pull apart
the Logiblocs in the direction shown.

Do not force the Logiblocs together.
This may hurt the connectors.

Do not place the Logiblocs themselves in water.

CONNECTORS

Содержание Super Inventor's















































Результаты поиска

Содержание Super Inventor's

Отзывы:

Похожие инструкции для Super Inventor's

Бренды по названию

Популярные бренды

Logiblocs Super Inventor's, Руководство изобретателя

Результаты поиска

Содержание Super Inventor's

Отзывы:

Похожие инструкции для Super Inventor's

Бренды по названию

Популярные бренды