Lochinvar LTL07575 Скачать руководство пользователя страница 3

Страница: 3 / 38

SAFE INSTALLATION, USE AND SERVICE

The proper installation, use and servicing of this water heater is extremely important to your safety and the safety of

others.

Many safety-related messages and instructions have been provided in this manual and on your own water heater to

warn you and others of a potential injury hazard. Read and obey all safety messages and instructions throughout this

manual. It is very important that the meaning of each safety message is understood by you and others who install,

use, or service this water heater.

All safety messages will generally tell you about the type of hazard, what can happen if you do not follow the safety

message, and how to avoid the risk of injury.

DANGER indicates an imminently

hazardous situation which, if not avoided,

will result in injury or death.

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible

injury or death.

WARNING indicates a potentially hazardous

situation which, if not avoided, could result

in injury or death.

CAUTION indicates a potentially hazardous

situation which, if not avoided, could result in

minor or moderate injury.

CAUTION used without the safety alert

symbol indicates a potentially hazardous

situation which, if not avoided, could result in

property damage.

WARNING

CAUTION

DANGER

APPROVALS

Low Lead Content

Содержание LTL07575







































Результаты поиска

Содержание LTL07575

Отзывы:

Похожие инструкции для LTL07575

Бренды по названию

Популярные бренды

Lochinvar LTL07575, Инструкция по эксплуатации

Результаты поиска

Содержание LTL07575

Отзывы:

Похожие инструкции для LTL07575

Бренды по названию

Популярные бренды