Lochinvar Armor 101 Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 28

background image

24

8

Troubleshooting

Installation / Replacement Procedure

1

3

2

UNPLUG THREE (3) WIRE HARNESSES

Figure 8-1

_Communication Board

1. Turn OFF the main electrical power to the appliance.

2. Turn OFF the main manual gas shutoff to the appliance.

3. Unplug the three (3) wire harnesses on the

communication board (see FIG. 8-1).

4. Remove the communication board (see FIG. 8-2).

5. Replace / install the new communication board.

6. Reconnect all three (3) wire harnesses unplugged in
Step

3.

7. Turn on the main electrical power and the main manual
gas

shutoff to the appliance.

8. Confi gure the communication board and unit controls

per this manual and resume operation.

DIR #2000555145 00

DIR #2000555145 00

DIR #2000555145 00

BACNET BOARD

Figure 8-2

_Control Panel w/ Communication Board

ModBus and BACnet Instructions

«
...
22
23
24
25
26
...
»

Содержание Armor 101 Series





























Отзывы:

Нет отзывов

Похожие инструкции для Armor 101 Series

Бренд: Javad Страницы: 35

Бренд: SMART Страницы: 15

Бренд: Zoom Страницы: 48

Бренд: Variscite Страницы: 18

Бренд: Arduino Страницы: 25

SRA311-008P8 Series

Бренд: Divio Страницы: 4

Бренд: Rajant Corporation Страницы: 40

Бренд: Aurora Страницы: 6

Бренд: Kontron Страницы: 62

Бренд: Matrix Switch Corporation Страницы: 48

SteelCentral NetExpress 470

Бренд: Riverbed Страницы: 140

Бренд: Grundfos Страницы: 40

Бренд: OWC Страницы: 9

Бренд: IBM Страницы: 8

MultiModem ISIHP-2S

Бренд: Multitech Страницы: 155

Cascade Express

Бренд: Riverbed Страницы: 92

Selenio SNP-GW-3GX32

Бренд: Imagine communications Страницы: 153

Бренд: Tachosys Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды