LNS ALPHA SL65 S Скачать руководство пользователя страница 92

Страница: 92 / 129

TROUBLESHOOTING

SERVICE MANUAL –ALPHA SL 65S

11. TROUBLESHOOTING

Errors detected by the PLC will be displayed on the HMI screen.

WARNING MESSAGES

Text alarm

Description

Solutions

Both sensor SQ5(0

position) and sensor
SQ3(15

position) are ON

or OFF.

Check both SQ3 and SQ5 to see if the
switches are broken.

Main cover CE switch
(SQ10) is separated from
the sensor block.

Manually close main cover.

Magazine cover CE
switch (SQ11) is
separated from sensor
block.

Manually close magazine protection
cover.

Optional retraction device
does not lock.

Lock retraction device.

After powering on the bar
feeder, this message
shown

before

pusher

returns to home position
(SQ2) in auto mode. The
bar feeder also operates
slowly at that time.

Once the pusher returns to home
position, this warning message will be
cleaned.

After powering on the bar
feeder, this message
shown

before

pusher

returns to home position
(SQ2) in manual mode.

Manually return pusher to home
position.

Содержание ALPHA SL65 S


































































































































Результаты поиска

Содержание ALPHA SL65 S

Отзывы:

Похожие инструкции для ALPHA SL65 S

Бренды по названию

Популярные бренды

LNS ALPHA SL65 S, Руководство по обслуживанию

Результаты поиска

Содержание ALPHA SL65 S

Отзывы:

Похожие инструкции для ALPHA SL65 S

Бренды по названию

Популярные бренды