LMI Technologies DynaVision S Series Скачать руководство пользователя страница 67

Страница: 67 / 68

PC DEMO HARDWARE AND SOFTWARE

Copyright LMI Technologies Inc. 2003

7.3.2.4

View/Diagnostics_Errors/Statistics

Power-up Count

This count refers to the number of times the sensor has been powered up over
its life span.

Checksum/CRC Errors

This count indicates the number of times the sensor has received bad data

packets. If Checksum count keeps increasing, further investigation of the
communications link is required.

Reset Count

This count refers to the number of internal restarts the sensor has gone
through caused by something other than the power going off and on

Command Errors

This count indicates the number of illegal commands the sensor has received
from the Host. This could indicate poor host software or a poor
communications link.

Calibration

This refers to the internal checking of the sensor to ensure its calibration tables
have not been corrupted.

Click on the

“

Update

”

button to update the display.

Содержание DynaVision S Series





































































Результаты поиска

Содержание DynaVision S Series

Отзывы:

Похожие инструкции для DynaVision S Series

Бренды по названию

Популярные бренды

LMI Technologies DynaVision S Series, Руководство пользователя

Результаты поиска

Содержание DynaVision S Series

Отзывы:

Похожие инструкции для DynaVision S Series

Бренды по названию

Популярные бренды