LJ&L CamoCam II Скачать руководство пользователя страница 8

Help Line  1-318-894-9490 

PAGE 8 

Using the Camera—

Continued

 

4. The camera has 9 pre-programmed settings allowing quick setup for most ap-
plications without the aid of a computer.  To select one of these settings, have the 
system power in the “ON” position and select one of nine settings using the 
wheel switch as illustrated below in figure (j). 
 
 
 
 

 
 
 
 
 
 
                               

Figure j

 

 
             
 
It really is that simple.  Try experimenting with different light levels, different 
camera angles and different programming configurations BEFORE using on an 
actual set.  You’ll find that your level of frustration will be minimal if you’ve had 
an opportunity to use the camera prior to depending on the camera for evidence. 
Amazingly, most people don’t use the camera until it’s needed and then it be-
comes a crash course over the phone with our help line trying to work out the 
bugs…..PRACTICE MAKES PERFECT!! 
 

CAUTION! 

Inserting a cassette into the camcorder is accomplished as follows.  Failure to 
read the camcorder operating guide may result in damage which is not cov-
ered under warranty. 
 

1.

To use the EJECT function, the power cable must be disconnected from the 
back of the camera. 

2.

Press the small blue button on the EJECT switch and slide it in the direction 
of the arrow. The cassette compartment automatically lifts up and opens. 

3.

Insert a cassette with the window facing out. 

4.

Gently close the cassette compartment by pressing the “PUSH” mark on the 
cassette compartment. 

The cassette compartment automatically goes 

down

 

 

PAGE 13 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

The external camera pictured 
above is a low light sensitive cam-
era.  It operates in .001 lux.  This 
means that it will get a good pic-
ture in near dark situations.  Used 
with the infrared illuminator, it will 
light up the night.  To connect it, 
attach the external camera cable to 
the EXTERNAL CAMERA port 
on the outside of the case.  Then plug the BULLET CAM POWER plug 
into the power jack and the BULLET CAM VIDEO plug into the back of 
the camera.  Focus the lens at the point you are aiming the camera at, and 
place it inside of the camouflaged tube.    

External Camera 

CamoCam™ 
Remote Video Surveillance 

Содержание CamoCam II











Отзывы: