INSTALLATION INSTRUCTIONS
JCBL Series Instructions
©2016 Acuity Brands Lighting, Inc. Rev 10/16 P4130 pg 1 of 7
One Lithonia Way, Conyers, GA 30012
Phone: 800-315-4963 www.lithonia.com
• To reduce the risk of death, personal injury or property damage from fire, electric shock,
falling parts, cuts/abrasions, and other hazards please read all warnings and instructions
included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment,
follow these general precautions.
• Installation and service of luminaires should be performed by a qualified licensed electrician.
• Maintenance of the luminaires should be performed by person(s) familiar with the
luminaires’ construction and operation and any hazards involved. Regular fixture
maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of
cleaning will depend on ambient dirt level and minimum light output which is acceptable
to user. Refractor/lens should be washed in a solution of warm water and any mild, non-
abrasive household detergent, rinsed with clean water and wiped dry. Should optical
assembly become dirty on the inside, wipe refractor/lens and clean in above
manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so
that no parts should have been damaged during transit. Inspect to confirm. Any part
damaged or broken during or after assembly should be replaced.
• Recycle: For information on how to recycle LED electronic products, please visit
www.EPA.gov
• These instructions do not purport to cover all details or variations in equipment nor to
provide every possible contingency to meet in connection with installation, operation, or
maintenance. Should further information be desired or should particular problems arise
which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter
should be referred to Acuity Brands Lighting, Inc.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: RISK OF PRODUCT DAMAGE
• Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer jacket or
damage wire insulations.
• Never connect an LED product to an unapproved dimmer pack. Contact ABL directly for any
dimmers not specifically recommended for the product.
• Unless individual product specifications deem otherwise: Allow for some volume of
airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material
that will prevent convection or conduction cooling.
• Unless individual product specifications deem otherwise: Maximum ambient temperature in
90ºC. Do not operate fixture at temperatures higher than this.
• Unless individual product specifications deem otherwise: Never mount in places where
fixture will be exposed to rain, high humidity, extreme temperature changes or restricted
ventilation.
• LEDs are polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding
equipment must be worn during all installation or servicing of the unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life,
or alter performance.
• There are no user serviceable parts insode the unit. Do not rewire, configure, or modify the
unit or attempt any repairs yourself. Additionally, field replacement of the LED assembly or
lamps is not allowed by UL standards at this time. In the unlikely event your unit may
require service, stop using the unit immediately and contact an ABL representative.
All luminaires that contain electronic devices that generate frequencies above 9kHz
from any component within the luminaire comply with one of the following Part 15 of
the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference recieved, including
interference that may cause undesired operation.
This device complies with Part 18 of the FCC Rules, but may cause interference with
cordless and cell phones, radios, televisions, and other electronic devices. To correct
the problem move the device away from the luminaire or lug into a different outlet.
This product may cause interference to radio equipment and should not be installed
near maritime safety communications equipment or other critical navigation or
communications equipment operating between 0.45-30MHz.
Failure to follow any of these instructions could void product warranties. For a
complete listing of product Terms and Conditions, please visit
www.acuitybrands.com
OUR BRANDS
Indoor/Outdoor: Lithonia Lighting, Carandinim Holophane, RELOC
Indoor Lighting: Gotham, Mark Architectural Lighting, Peerless, Renaissance
Lighting, Winona Lighting
Outdoor Lighting: American Electric Lighting, Antique Street Lamps, Hydrel, Tersen
Controls: DARK TO LIGHT, Lighting Control & Design, ROAM, Sensor Switch,
Synergy
Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out
of improper or careless installation or handling of its products.
• Disconnect or turn off power before installation or servicing.
• Verify that supply voltage is correct by comparing it with the luminaire
label information.
• Make all electrical and grounded connections in accordance with the National
Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved recognized
wire connectors.
WARNING RISK OF ELECTRIC SHOCK
• Wear gloves and safety glasses at all times when removing luminaire from carton,
installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
CAUTION RISK OF INJURY
• Allow lamp/fixture to cool before handling. Do not touch enclosure or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer’s warnings, recommendations and restrictions for: driver
type, burning position, mounting locations/methods, replacement and recycling.
WARNING RISK OF BURN
• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances
affected by heat or drying.
CAUTION RISK OF FIRE
