Lite Machines LMH 100 Скачать руководство пользователя страница 10

Страница: 10 / 89

equirements

This section lists the equipment, tools and materials needed to assemble and

operate the Lite Machines

Model 110

™ helicopter. Note that a specialized helicopter

radio and electronic gyro are not required. Although helicopter radios may be used,

they are usually more expensive than airplane radios and do not appreciably improve

the flying qualities of the

Model 110

helicopter.

Federal law requires that radio controlled model aircraft use specific radio

frequencies. Check with your hobby dealer or local club to find a radio frequency

within the appropriate band that is not popular with other fliers in your area (since two

aircraft cannot fly on the same frequency simultaneously), and is not subject to local

interference (some phone pagers may cause interference).

Radio

1. Standard four (4) channel airplane-style transmitter (Hitec

Focus 4H Micro

Futaba

Attack

, Airtronics

Vanguard

, JR

F400

etc.. Most radio manufacturers

normally supply servo mounting hardware and extra servo control arms.)

2. Four (4)

MICRO

servos (Hitec

HS-80/HS-81

, Futaba

3101

, Airtronics

94501

, JR

341

, etc.)

3. 250 mAh to 600 mAh battery pack, flat style
4. 2-piece Dean’s antenna (This short whip-style antenna replaces the long wire

antenna on the radio receiver. Long antennas used on airplanes get tangled in

the rotor blades of the

Model 110

helicopter.)

5. Servo mounting hardware (if not supplied by radio manufacturer)
6. 3" x 6" x 1/4" latex foam rubber sheet (to protect the receiver from vibration and

minimize crash damage)

7. Two small plastic bags (to protect the receiver and battery from dirt and oil)
8. Newspaper rubber bands (to secure radio battery and receiver)

Engine and Fuel

1. Norvel

Vmax-6

helicopter engine (The

Vmax-6

has special cylinder porting and a

carburetor venturi sized for easier starting. Do not use super-revving racing

engines such as the Norvel

AME

. Racing engines are too powerful and run too

fast for the

Model 110

helicopter, and can dangerously over-drive the rotor

system. The

Model 110

helicopter is not warranted for use with any engines

except for the Norvel

Vmax-6).

2. Lite Machines

SpiraLite Speed

™ or Norvel

Freedom XL

glowplug

Construction Manual

Requirements

LITE MACHINES

3-1

Содержание LMH 100


























































































Результаты поиска

Содержание LMH 100

Отзывы:

Похожие инструкции для LMH 100

Бренды по названию

Популярные бренды

Lite Machines LMH 100, Руководство по монтажу

Результаты поиска

Содержание LMH 100

Отзывы:

Похожие инструкции для LMH 100

Бренды по названию

Популярные бренды