Liquid Controls POD1 Скачать руководство пользователя страница 22

Страница: 22 / 24

Pulse Output Device

Get the latest PDF manual:

https://www.lcmeter.com/resources/technical/manuals

Mobile/online version of this manual:

https://www.lcmeter.com/manuals

7. Reassemble the unit.

SIGNAL OUTPUT

The diagram below shows the voltage output for a clockwise rotation of the Pulse Output
Device (POD) with Channel A leading Channel B. For reverse flow applications
(counterclockwise) Channel B leads Channel A.

NOTE:

Quadrature channel voltage output is 90° out of phase with Channel B.

POD Wiring Schematics

Single Channel Applications – SP4000, SP3850, IT400

Follow these steps when wiring the POD:

1. Use metallic conduit with individual

wires or use 3 conductor, 22
AWG, shielded cable.

2. Strip 1½" off of outer sheathing.

Remove exposed shield and drain
wire and then tape.

3. Strip ¼" insulation from each

conductor and connect to the
terminal blocks.

Содержание POD1

























Результаты поиска

Содержание POD1

Отзывы:

Похожие инструкции для POD1

Бренды по названию

Популярные бренды

Liquid Controls POD1, Инсталляционные компоненты

Результаты поиска

Содержание POD1

Отзывы:

Похожие инструкции для POD1

Бренды по названию

Популярные бренды