Lipco HSA 30 Скачать руководство пользователя страница 9

Страница: 9 / 32

Instructions

Hydraulic shaker HSA 30

9 - 32

220074-01-EN BA HSA 30 / 28.09.2019

•

Operate machine only with PTO drive unit fully protected, i.e.
universal joint shaft completely covered and additional protection
on tractor and

LIPCO HSA

. Make sure that the universal joint

shaft connections are securely locked!

•

Attach the safety chain to avoid turning of PTO drive shaft pro-
tection during operation!

•

The operator is responsible for compliance with applicable acci-
dent prevention regulations, in addition to the generally recog-
nized safety, occupational health and traffic safety regulations!

•

Note:
Because of the maximum allowable additional tractor load,
please refer to adequate information, given by tractor manufac-
turer!

Lifting the

LIPCO HSA

with tractor’s 3-point linkage will increase

tractor’s axle load!

•

Note:
Keep in mind the condition for maximum allowable slop angle of
the combination of t

LIPCO HSA.

Check especially the instructions of the tractor manufacturer with
regard to the maximum allowable slope angle with attached ma-
chines / load.

This concerns driving parallel to the slope or downslope.

Any operation not adapted to local conditions

can cause serious

personal injuries or material damages because of tilting of the
combination of t

LIPCO HSA.

Содержание HSA 30

































Результаты поиска

Содержание HSA 30

Отзывы:

Похожие инструкции для HSA 30

Бренды по названию

Популярные бренды

Lipco HSA 30, Оригинальное руководство пользователя

Результаты поиска

Содержание HSA 30

Отзывы:

Похожие инструкции для HSA 30

Бренды по названию

Популярные бренды